![]() |
![]() |
#1 |
Member
Join Date: Mar 2014
Location: Downey
Posts: 88
|
Kayak leaks
It's a orange trident 15 if that matters. Thanks. |
![]() |
![]() |
![]() |
#2 |
Member
Join Date: Mar 2014
Location: Downey
Posts: 88
|
anybody??
|
![]() |
![]() |
![]() |
#3 |
Large Member
Join Date: Jul 2012
Location: La Verne, CA
Posts: 1,004
|
Most smaller above the water line leaks can be remedied with the product linked below
http://www.kayakfishingsupplies.com/marine-goop |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Sep 2014
Posts: 193
|
I just found a crack next to one of the drain plugs in the seat of my x factor. Would that goop be ideal for that as well? uploadfromtaptalk1435622659646.jpg
|
![]() |
![]() |
![]() |
#5 | |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
Quote:
__________________
![]() ![]() |
|
![]() |
![]() |
![]() |
#6 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
For the OP, you can weld holes or a simple fix is a little goop on a stainless bolt and nyloc, factory fresh look. rod holders sound like they need a bead of goop then reinstall.
__________________
![]() ![]() |
![]() |
![]() |
![]() |
#7 |
Team Get $$
Join Date: Feb 2013
Location: San Diego, CA
Posts: 841
|
^ and there u have it. Problem solved!
__________________
The "Y" is silent 2012 Olive PA 12 2011 Papaya Outback |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Sep 2014
Posts: 193
|
|
![]() |
![]() |
![]() |
#9 | |
Member
Join Date: Mar 2014
Location: Downey
Posts: 88
|
Quote:
I'm not sure what to do with the mounts tho. They are in an area that I want to use for rudder foot pedals |
|
![]() |
![]() |
![]() |
#10 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
weld em or hot glue em, you can take a razor blade to the hot glue and make it nice and flush.
__________________
![]() ![]() |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Mar 2010
Location: San Diego
Posts: 2,385
|
I recommend all that own a kayak invest in a heat gun, and even a plastic welding iron. you can get them at harbor freight for really low prices. Check out youtube on welding kayaks,
https://www.youtube.com/results?sear...=kayak+welding It's really not that tough, but be careful with the heat gun, if you hold it in one place for too long you might have an issue. Other idea is take it to Andy and OEX and let them do it for you.
__________________
No better time than being on the water, God Bless, JimmyZ ![]() |
![]() |
![]() |
![]() |
#12 |
Member
Join Date: Mar 2014
Location: Downey
Posts: 88
|
Adress
Thanks guys i will give it a try. Heating or welding scares me but I'll have to man up
Last edited by Sir LJ; 07-01-2015 at 12:33 PM. Reason: Edit |
![]() |
![]() |
![]() |
#13 |
Junior
Join Date: Apr 2014
Location: La Habra
Posts: 4
|
First Repair
For your first repair, I'd stay away from the heat gun and use a plastic welder (soldering iron). If you hold the heat gun in one place too long it can overheat the hull and start melting it, making your small hole a large one in an instant. whichever method you try, keep a cold damp rag handy to slap on the repair and cool the plastic should it overheat. You'll need some plastic to fill the holes, HDPE. A Home Depot bucket is HDPE and its even Orange. Cut a strip about 1/4" wide by 6" long. Hold the end over the hole and push down with the soldering iron. as the strip melts, it will sink into the hole. Then make some small circles with the soldering iron to meld the plastic. Repeat until its built up above the surrounding area then let it cool. sand it down nice and smooth and happy paddling!
soldering gun.jpg |
![]() |
![]() |
![]() |
|
|