hobie tank repairs - Kayak Fishing Adventures on Big Water’s Edge

TJones · 01-06-2013, 08:15 AM

yesterday i had two serious fails . first i filled the tank with macs , and while they were slashing around to the brims capacity, broke my connection where i had by passed my failed switch. i notice the the macs were getting sleepy eyed and quiet.

. so i release them , did a temporary fix , and back in business. at end of day when i went to unplug battery , pulled wire out of socket. is it time to rewire the tank? tank is more than a couple years old. any input would be appreciated. having the bait tank is great , but it always seems like something is always going wrong .first switch , thens its batteries , then clogs with pump. now wiring issues .

. as far as clogs with intake and sea grass, i did discover something pretty good. i bought a screen from home depot that has rubber on edges , i believe used for sink replacement . i trimmed the rubber a little , and placed behind black nipple of intake tube. it does make it more restrictive , but not enough to hinder flow. keeps grass out. one problem solved, for now. thanks again for any suggestions or help with wire issues. when i trimmed back wire to reconnect , i noticed it looks corroded under insulation and some what brittle. is that normal?

jaws197 · 01-06-2013, 10:07 AM

Had the same problem with my hobie tank at the switch, had to scrape off the clear insulation and re-solder the corroded terminal switch had failed then marine gooped the heck out of it.

I'm going to try your suggestion about the intake as I am tired of it sucking up EVERY piece of eel grass in the ocean!!! You would think that a tank that cost $200 would be made a little better with a little more thought about it's potential for pulling in foreign material (eel grass)!

TJones · 01-06-2013, 11:02 AM

there will be 2 screen replacements .about the size of a penny. i trimmed almost all the rubber on edges of screen and gently pressed it into the intake tube after removing the black nipple. replace black nipple and you are done. after a few launching and landings some sand will collect on screen, but not enough to stop flow . a few good pumps with peddles to get flow going to prime the tank is all that is needed. gallons per minute flow rate is reduced , but nothing that affects bait. one thing is for sure . grass is not going up inside.

. been using for about 4 outings . so far , so good.

DanaPT · 01-06-2013, 12:14 PM

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top. Because of the screen it's difficult to plug the in-take tube. IF something does get caught, moving around usually dislodges the debris..

Used to get clogged in the kelp until I began using this solution.

BrokeLoser · 01-06-2013, 12:24 PM

Quote:

Originally Posted by DanaPT

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top. Because of the screen it's difficult to plug the in-take tube. IF something does get caught, moving around usually dislodges the debris..

Used to get clogged in the kelp until I began using this solution.

Awesome idea...is that found at Home Depot? Does it restrict flow a bunch?

StinkyMatt · 01-06-2013, 12:42 PM

About a year ago I got tired of the connections and switch issues. Completely eliminated the switch and rewired the tank. At the battery I use a red/white connector like the ones found at automotive stores for .99 cents. When you make a wire to wire connection put on shrink tubing And then goop it all over. When you are ready to turn on tank, you turn around and plug in, simple.

I have not had one tank related issue in a year.

BrokeLoser · 01-06-2013, 12:47 PM

Quote:

Originally Posted by StinkyMatt

About a year ago I got tired of the connections and switch issues. Completely eliminated the switch and rewired the tank. At the battery I use a red/white connector like the ones found at automotive stores for .99 cents. When you make a wire to wire connection put on shrink tubing And then goop it all over. When you are ready to turn on tank, you turn around and plug in, simple.

I have not had one tank related issue in a year.

So no on/off switch at all?

TJones · 01-06-2013, 07:01 PM

i did same . ditched the switch. i used cheap barrel connection and that is why it popped off. along with the fact i had about 30 ragging macs slashing around.

. dogs were really all over my ass at lj squid grounds yesterday. if i went to deeper water i wanted to be prepared. i will try your idea and run new wire. thx.

TJones · 01-09-2013, 05:20 PM

put a screw on wire connector like the stock one . also some marine goop. the mistake i made when i bypassed the switch was , i used a barrel connector. this time i used some metal staples to secure wires together to alleviate some stress, along with some additional wire ties. tested it out, and we are ready to go. i also bought i new dip tube from the local pet supply store . i cut it to about 14 " . 4 - 5 " deep into kayak and about 9 '" height inside tank . this will give me good support into kayak to prevent tank from moving and a nice high water level to support 30 ragging macs slashing about in tank.

thx everyone for help and suggestions.

maui jim · 01-10-2013, 07:41 AM

Quote:

Originally Posted by DanaPT

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top.

Used to get clogged in the kelp until I began using this solution.

I Never used a zip tie on a condom...

Strange comparison....

jorluivil · 01-10-2013, 10:00 AM

I followed what Matt did and went straight battery to pump. Unlike Matt, the thing that I don't like about it is the 'reach around'.

jorluivil · 01-10-2013, 10:01 AM

Quote:

Originally Posted by BrokeLoser

Awesome idea...is that found at Home Depot?

????

01-10-2013, 10:37 AM

I've been through 5 switches on my tank in 4 months, same problem over and over. Granted I fish 3-4 days a week minimum so it see's a lot of abuse.

Corrosion and snapping at the wire to the switch connection. It's been under warranty and the shop kept assuring me it they would fix it.

Finally, I just asked for the switch and I would take care of it myself. I covered the switch where the wires connect with so much marine goop and I haven't had an issue as of yet.

TJones · 01-10-2013, 02:48 PM

i bypassed it, and hooked up that barrel connector to make straight connection, without using marine goop. lasted a good while, until i over crammed the tank with 30 ragging macs.

my stock hobie switch was pretty good , it was coated with red latex? to try and prevent failure. the switch failed somewhere inside , i believe. unlike some users on this site , i like the occasional reach around .

bypassing sucks ess. but it is one less thing to worry about . after all the bucks i spent , i did not want to spend another 30 for a switch from west marine. thanks again for any input .

01-06-2013, 08:15 AM	#1
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	hobie tank repairs yesterday i had two serious fails . first i filled the tank with macs , and while they were slashing around to the brims capacity, broke my connection where i had by passed my failed switch. i notice the the macs were getting sleepy eyed and quiet. . so i release them , did a temporary fix , and back in business. at end of day when i went to unplug battery , pulled wire out of socket. is it time to rewire the tank? tank is more than a couple years old. any input would be appreciated. having the bait tank is great , but it always seems like something is always going wrong .first switch , thens its batteries , then clogs with pump. now wiring issues . . as far as clogs with intake and sea grass, i did discover something pretty good. i bought a screen from home depot that has rubber on edges , i believe used for sink replacement . i trimmed the rubber a little , and placed behind black nipple of intake tube. it does make it more restrictive , but not enough to hinder flow. keeps grass out. one problem solved, for now. thanks again for any suggestions or help with wire issues. when i trimmed back wire to reconnect , i noticed it looks corroded under insulation and some what brittle. is that normal?

01-06-2013, 11:02 AM	#3
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	look for small package there will be 2 screen replacements .about the size of a penny. i trimmed almost all the rubber on edges of screen and gently pressed it into the intake tube after removing the black nipple. replace black nipple and you are done. after a few launching and landings some sand will collect on screen, but not enough to stop flow . a few good pumps with peddles to get flow going to prime the tank is all that is needed. gallons per minute flow rate is reduced , but nothing that affects bait. one thing is for sure . grass is not going up inside. . been using for about 4 outings . so far , so good.

01-06-2013, 07:01 PM	#8
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	thx matt i did same . ditched the switch. i used cheap barrel connection and that is why it popped off. along with the fact i had about 30 ragging macs slashing around. . dogs were really all over my ass at lj squid grounds yesterday. if i went to deeper water i wanted to be prepared. i will try your idea and run new wire. thx.

01-09-2013, 05:20 PM	#9
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	got the new wire installed put a screw on wire connector like the stock one . also some marine goop. the mistake i made when i bypassed the switch was , i used a barrel connector. this time i used some metal staples to secure wires together to alleviate some stress, along with some additional wire ties. tested it out, and we are ready to go. i also bought i new dip tube from the local pet supply store . i cut it to about 14 " . 4 - 5 " deep into kayak and about 9 '" height inside tank . this will give me good support into kayak to prevent tank from moving and a nice high water level to support 30 ragging macs slashing about in tank. thx everyone for help and suggestions.

01-10-2013, 10:00 AM	#11
jorluivil Senior Member Join Date: Apr 2010 Posts: 6,856	I followed what Matt did and went straight battery to pump. Unlike Matt, the thing that I don't like about it is the 'reach around'. __________________ www.facebook.com/Teamsewer

01-06-2013, 10:07 AM	#2
jaws197 Senior Member Join Date: Apr 2012 Location: Poway, CA Posts: 148	Had the same problem with my hobie tank at the switch, had to scrape off the clear insulation and re-solder the corroded terminal switch had failed then marine gooped the heck out of it. I'm going to try your suggestion about the intake as I am tired of it sucking up EVERY piece of eel grass in the ocean!!! You would think that a tank that cost $200 would be made a little better with a little more thought about it's potential for pulling in foreign material (eel grass)!

01-06-2013, 12:42 PM	#6
StinkyMatt Senior Member Join Date: Jun 2010 Location: Under a bridge Posts: 2,169	About a year ago I got tired of the connections and switch issues. Completely eliminated the switch and rewired the tank. At the battery I use a red/white connector like the ones found at automotive stores for .99 cents. When you make a wire to wire connection put on shrink tubing And then goop it all over. When you are ready to turn on tank, you turn around and plug in, simple. I have not had one tank related issue in a year.

01-10-2013, 10:37 AM	#13
Drake Guest Posts: n/a	I've been through 5 switches on my tank in 4 months, same problem over and over. Granted I fish 3-4 days a week minimum so it see's a lot of abuse. Corrosion and snapping at the wire to the switch connection. It's been under warranty and the shop kept assuring me it they would fix it. Finally, I just asked for the switch and I would take care of it myself. I covered the switch where the wires connect with so much marine goop and I haven't had an issue as of yet.

01-10-2013, 02:48 PM	#14
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	after the first switch i bypassed it, and hooked up that barrel connector to make straight connection, without using marine goop. lasted a good while, until i over crammed the tank with 30 ragging macs. my stock hobie switch was pretty good , it was coated with red latex? to try and prevent failure. the switch failed somewhere inside , i believe. unlike some users on this site , i like the occasional reach around . bypassing sucks ess. but it is one less thing to worry about . after all the bucks i spent , i did not want to spend another 30 for a switch from west marine. thanks again for any input .