Installing fish finder

[sammysamsam]

Originally Posted by jorluivil

I'm not in the 714 area but what trouble are you having? Post some details and I can assure you that you'll have countless responses and the how and the what's of FF installs.

Originally Posted by bus kid

Jorge is the master of fishfinder installation, he will come to you for a fee, plus $.75 a mile traveled. Jorge I get 10% for the plug.

just kidding, follow his advice post up.

well i guess the part that seems really hard is installing the transducer. I read the thread about installing a wet mount and would like to do it that way. Just seems a little daunting for me to do it like that.

[KennyHill]

Just put your transducer in a ziplock sandwitch bag with alittle bit of water in it and set it in place when you get out on the water. quick and easy.

enless your looking for permanent install. That seems to be the easiest way to me. No glue, no holes, no air bubbles, no problems.

[sammysamsam]

Originally Posted by KennyHill

Just put your transducer in a ziplock sandwitch bag with alittle bit of water in it and set it in place when you get out on the water. quick and easy.

enless your looking for permanent install. That seems to be the easiest way to me. No glue, no holes, no air bubbles, no problems.

Wow, i have never heard of doing it that way. Do you get good results? where would you set it in place exactly?

[Deamon]

Originally Posted by KennyHill

Just put your transducer in a ziplock sandwitch bag with alittle bit of water in it and set it in place when you get out on the water. quick and easy.

enless your looking for permanent install. That seems to be the easiest way to me. No glue, no holes, no air bubbles, no problems.

Out of curiosity, I'd like to see how the water seal occurs when there's a wire coming out of the ziplock bag...maybe post a picture of your set-up? Framed up tight to keep the transducer from moving around...or lake flat conditions only (no surf zone entry)?

[RedSledTeam]

Here's how I did it... simple and 6 months later it still works great too! Thanks for the How-to tip Leo!

[sammysamsam]

Originally Posted by RedSledTeam

Here's how I did it... simple and 6 months later it still works great too! Thanks for the How-to tip Leo!

doesnt the transducer move around a lot installed like that?

[KennyHill]

With the bag i fill it up just enough to cover the transducer maby 2'' of water thats it. Then zip it up all the way to the wire. Once im out past the surf zone i just get into my hatch and reposition the transducer.

You get clear readings altho the water temp will be off. At least mine always is.

This trick was shown to me by another member over 2 years ago out on the water. I still use it till this day. I dont have a problem with it moving around on me and i seem to only get to fish when the conditions are at there worst haha.

[flydigital]

Originally Posted by RedSledTeam

Here's how I did it... simple and 6 months later it still works great too! Thanks for the How-to tip Leo!

That's just about how I do it! Although mine is just tie-wrapped to the hobie sailing mast.

It doesn't move around, only when flipping the kayak upside down during storage, etc... but you just move it into position while you are loading your gear and it stays put. Simple and sonar performance is much better than a goop install.

[sammysamsam]

Originally Posted by RedSledTeam

Here's how I did it... simple and 6 months later it still works great too! Thanks for the How-to tip Leo!

Originally Posted by KennyHill

With the bag i fill it up just enough to cover the transducer maby 2'' of water thats it. Then zip it up all the way to the wire. Once im out past the surf zone i just get into my hatch and reposition the transducer.

You get clear readings altho the water temp will be off. At least mine always is.

This trick was shown to me by another member over 2 years ago out on the water. I still use it till this day. I dont have a problem with it moving around on me and i seem to only get to fish when the conditions are at there worst haha.

Originally Posted by flydigital

That's just about how I do it! Although mine is just tie-wrapped to the hobie sailing mast.

It doesn't move around, only when flipping the kayak upside down during storage, etc... but you just move it into position while you are loading your gear and it stays put. Simple and sonar performance is much better than a goop install.

so its been a few months and now im finally getting back into fishing and putting this thing in.

Im gonna try it with the bungee cord wrapped like that and then try the zip lock method just for kicks. If i dont get good readings, ill try the foam method. Thanks all. ill report back.

Anyone have any other ideas?

[RK]

Same here on the bungie to the scuppers gravity add water mount, works really good

[IB Fish"N"]

I just took a piece of foam about 6"X6" and about 2" thick cut shape of transducer then glued it down inside after that put water in and press transducer down inside and make it level and your done soak up extra water. Great picture.

[RedSledTeam]

What glue did you use?

[Jimmyz123]

Originally Posted by sammysamsam

well i guess the part that seems really hard is installing the transducer. I read the thread about installing a wet mount and would like to do it that way. Just seems a little daunting for me to do it like that.

Use the Electrical Putty installation method it's easy, stays in place and the readings are dead on.
http://www.youtube.com/watch?v=GEZ9_C1iKP0

http://www.youtube.com/watch?v=3u1d3...eature=related

This is what I used and here are the results.


It works and it's very easy.

[sammysamsam]

Originally Posted by Jimmyz123

Use the Electrical Putty installation method it's easy, stays in place and the readings are dead on.
http://www.youtube.com/watch?v=GEZ9_C1iKP0

http://www.youtube.com/watch?v=3u1d3...eature=related

This is what I used and here are the results.


It works and it's very easy.

Seems simple enough also. Lost of ideas here. Thanks!

seeing as the 6v 12ah batteries are so cheap, i might as well buy one of those and dedicate my 12v to the ff. There are diff types of 6v batteries tho.
Does it matter which kind i get? sealed acid, gel, etc?

[kobra]

Same type as your 12 volt. Gel type.