Lowrance Elite Chirp Fishfinders

[Raskal311]

Ohh crap


Lowrance transducers:

Compatible (Fits Lowrance Ready housing):
000-0106-72 HST-WSBL 83/200 Skimmer Blue Connector
000-10976-001 HDI Skimmer 83/200 + 455/800
000-10260-001 DSI Skimmer 455/800
000-0106-48 HST-WSU Uniplug 83/200 Skimmer

Incompatible (Too large for Lowrance Ready housing):
000-0106-77 HST-DFSBL 50/200 Skimmer
000-11302-001 Airmar TM150
000-11062-001 Airmar P66
000-10977-001 HDI Skimmer 50/200 + 455/800
000-10802-001 StructrureScan HD

[Murray]

Originally Posted by Raskal311

Ohh crap


Lowrance transducers:

Compatible (Fits Lowrance Ready housing):
000-0106-72 HST-WSBL 83/200 Skimmer Blue Connector
000-10976-001 HDI Skimmer 83/200 + 455/800
000-10260-001 DSI Skimmer 455/800
000-0106-48 HST-WSU Uniplug 83/200 Skimmer

Incompatible (Too large for Lowrance Ready housing):
000-0106-77 HST-DFSBL 50/200 Skimmer
000-11302-001 Airmar TM150
000-11062-001 Airmar P66
000-10977-001 HDI Skimmer 50/200 + 455/800
000-10802-001 StructrureScan HD

I have an old outback and purchased a magnetic transducer mount for my 50/200 transducer. Checking out my system tomorrow and will try to report afterwards. Fishfindermounts.com fyi

[Dave Legacy]

Originally Posted by Murray

I have an old outback and purchased a magnetic transducer mount for my 50/200 transducer. Checking out my system tomorrow and will try to report afterwards. Fishfindermounts.com fyi

I have been looking forward to hearing more about these mounts. It seems like a pretty good solution.

[Murray]

Here is a link to the best explanation I have read regarding the benefits of Downscan Overlay.

http://www.fishfindersource.com/lowr...-5-hdi-review/

[Murray]

Worked fine in Oceanside Harbor. The reason I went this route is convenience. Did not want to try and install my 50/200 BIG transducer via putty, goop, container with water, etc. I transport my yak upside down on my car so above mounting techniques were a concern. Need to test in the surf to determine whether to attach transducer to the mounting system before or after launch/landing. Probably will be determined by size of surf. When attaching my heavy transducer, magnets slipped a bit on the smooth surface of my yak. Manufacturer is shipping me some rubber pads that should take care of any slipping.

[Dave Legacy]

Originally Posted by Murray

Worked fine in Oceanside Harbor. The reason I went this route is convenience. Did not want to try and install my 50/200 BIG transducer via putty, goop, container with water, etc. I transport my yak upside down on my car so above mounting techniques were a concern. Need to test in the surf to determine whether to attach transducer to the mounting system before or after launch/landing. Probably will be determined by size of surf. When attaching my heavy transducer, magnets slipped a bit on the smooth surface of my yak. Manufacturer is shipping me some rubber pads that should take care of any slipping.

I bet you could goop the inner magnet in so you can easily pop the transducer into place after a surf launch.

[Murray]

Originally Posted by Dave Legacy

I bet you could goop the inner magnet in so you can easily pop the transducer into place after a surf launch.

No need to goop as the magnets are attached before launch/land. The only item to be attached before or after is the arm that the transducer is attached to. Not a big deal......just do not drop the screw into the water when attaching. Might be a good idea to get a spare just in case.

[acorad]

Originally Posted by Murray

Here is a link to the best explanation I have read regarding the benefits of Downscan Overlay.

http://www.fishfindersource.com/lowr...-5-hdi-review/

Great link.

Andy

[Murray]

Originally Posted by Murray

Here is a link to the best explanation I have read regarding the benefits of Downscan Overlay.

http://www.fishfindersource.com/lowr...-5-hdi-review/

After more research, it seems like choosing the page that shows sonar/downscan is the best way to go. Overlay seems a bit difficult to see downscan image when it is combined with sonar. Will test more when I fish la jolla.......deeper water.

[YakDout]

Originally Posted by Raskal311

Ohh crap





Lowrance transducers:



Compatible (Fits Lowrance Ready housing):

000-0106-72 HST-WSBL 83/200 Skimmer Blue Connector

000-10976-001 HDI Skimmer 83/200 + 455/800

000-10260-001 DSI Skimmer 455/800

000-0106-48 HST-WSU Uniplug 83/200 Skimmer



Incompatible (Too large for Lowrance Ready housing):

000-0106-77 HST-DFSBL 50/200 Skimmer

000-11302-001 Airmar TM150

000-11062-001 Airmar P66

000-10977-001 HDI Skimmer 50/200 + 455/800

000-10802-001 StructrureScan HD

I have your HST-Dfsbl transducer listed currently in my lowrance ready. 30 second modification. Ive had an ever bigger transducer in before also. Let me know if you want pics.

[Raskal311]

Originally Posted by YakDout

I have your HST-Dfsbl transducer listed currently in my lowrance ready. 30 second modification. Ive had an ever bigger transducer in before also. Let me know if you want pics.

yes please, that would be great!