Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion
Home Forum Online Store Information LJ Webcam Gallery Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
Old 04-03-2014, 12:21 AM   #1
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
New battery box set up and xfactor rigging

So I'm going to start my build.
This is the first thing today
The new bright orange battery box
1 9ah 12v fishfinder/aux batt
1 12ah 6v bait pump

Plan is to run 2 out lines to waterproof "trailer" plug disconnects so I can remove the box if needed.

I also picked up the stuff to make my bait tank and also a bunch of Scotty parts and lastly a mark 4 hdi unit, I plan on changing to a elite 5hdi or better soon and move the mark 4 to the gfs yak
Attached Images
File Type: jpg image.jpg (61.5 KB, 335 views)
live2fishy is offline   Reply With Quote
Old 04-05-2014, 12:10 AM   #2
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
Haven't had much time to work on this but step 2 wire the box and keep it waterproof...
Attached Images
File Type: jpg image.jpg (60.6 KB, 281 views)
live2fishy is offline   Reply With Quote
Old 04-05-2014, 12:12 AM   #3
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
Bait tank, fish finder and rod holders coming soon. Any input appriciated
Thanks!
live2fishy is offline   Reply With Quote
Old 04-05-2014, 10:52 AM   #4
FISH11
Member
 
FISH11's Avatar
 
Join Date: Aug 2013
Location: Pine Valley when not fishing La Jolla
Posts: 2,643
Are you going to install an on / off waterproof switch for the bait tank pump. On the battery box is the best place (keeps it most protected from the salt water). I have my battery box attached to the inside of the hull just to the side of the center hatch of my X Factor. It is held in place by 2 Velcro strips that are glued to the inside of the hull and the back of the battery box ( I used 3M weatherstrip cement), that keeps the box from sliding around, is still removable and does not take up room in the center hatch bag. Good luck on you project. Mark
__________________
MARK ......... 2016 MALIBU X FACTOR, 2020 SOLO SKIFF (Fishing Kayak on Steroids )
FISH11 is offline   Reply With Quote
Old 04-05-2014, 12:58 PM   #5
solyluna
Member
 
solyluna's Avatar
 
Join Date: Jun 2013
Posts: 73
I have one 32 amps battery for my bait tank ff and bilge
And it seats inside the yak between the 2 square hatch
solyluna is offline   Reply With Quote
Old 04-18-2014, 05:29 PM   #6
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
So finishing up my rigging, wiring up my bait tank
Attached Images
File Type: jpg image.jpg (64.5 KB, 197 views)
live2fishy is offline   Reply With Quote
Old 04-18-2014, 05:30 PM   #7
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
Switch
Attached Images
File Type: jpg image.jpg (44.9 KB, 197 views)
live2fishy is offline   Reply With Quote
Old 04-18-2014, 06:46 PM   #8
Raskal311
Senior Member
 
Raskal311's Avatar
 
Join Date: Mar 2011
Location: Santa Ana/Westminster
Posts: 1,256
whats the make and model of that orange box?
__________________
Kevin
Yellow PA12
Raskal311 is offline   Reply With Quote
Old 04-19-2014, 07:33 PM   #9
solyluna
Member
 
solyluna's Avatar
 
Join Date: Jun 2013
Posts: 73
Your bait tank is too far back
I think
Malibu have a tank that seat inside
That slanted hatch
And working with the suppers (drain & intake)
solyluna is offline   Reply With Quote
Old 04-19-2014, 08:05 PM   #10
Iceman
Administrator
 
Iceman's Avatar
 
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
I did something similar about 5 years ago with 2 6 volt, one in series 12 and 6 volt power



http://www.bigwatersedge.com/bwevb/s...hlight=battery
__________________
Iceman is offline   Reply With Quote
Old 04-19-2014, 08:15 PM   #11
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
Man I wish I had those plugs on the box, what brand are those?

I can reach easier extended arm vs contorted twisted arm if its too close you know
live2fishy is offline   Reply With Quote
Old 04-19-2014, 08:23 PM   #12
live2fishy
Fish killer
 
Join Date: Jun 2008
Location: Surfside
Posts: 105
Quote:
Originally Posted by Raskal311 View Post
whats the make and model of that orange box?
It's a sea horse box I think is the brand it was like 20 bucks from orvac electronics in Fullerton
live2fishy is offline   Reply With Quote
Old 04-19-2014, 09:36 PM   #13
Iceman
Administrator
 
Iceman's Avatar
 
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
Sea Dog deck connectors
__________________
Iceman is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 05:30 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.