Polishing Hull of Proangler - Kayak Fishing Adventures on Big Water’s Edge

06-19-2012, 10:46 AM

My PA is pretty scratched up from the previous owner. I was wondering if there was a good way to polish it up and make it look better. I was thinking of either using a rubbing compound/polishing compound combo or lightly lightly lightly wetsanding it with really fine sand paper. If it gets a matte look to it that way I'm totally ok with that.
I just don't want to thin the hull anymore than I have to. Thanks

MrM · 06-19-2012, 11:08 AM

Interesting post... I would love to hear if anyone has info on this. I've got a scratch or two from beach landings I'd like to fill in and smooth out.

mrJB · 06-19-2012, 11:46 AM

Polyethylene will buff and/or sand out to a certain extent, just a lot of work and will never get a supershine. It will only get the very lightest scratches. You can get somewhat deeper scratches by scraping, either with a cabinet scraper or razor blade, but then you are taking off some material.

I've done it - scraped, wet sanded, buffed with a buffer, on and on. Just depends on how much work you want to put into it. A heat gun will put some shine back into it but there are potential risks...

My $.02, clean it up, put some sacrificial tape strips on the wear area, and use some plastic protectant on it Try to keep it nice from this point on and wash it down after every outing...

mtnbykr2 · 06-19-2012, 11:51 AM

"battle scars"

06-19-2012, 12:51 PM

The only reason I want to clean it up is to sell it. I don't want to sell it looking like it fell off my truck

jorluivil · 06-19-2012, 05:58 PM

Quote:

Originally Posted by Drake

The only reason I want to clean it up is to sell it. I don't want to sell it looking like it fell off my truck

Its not a woman you're selling

. Gys will really not care about the 'wear n tear' but they will enjoy the stories that are behind them

Chief Gunner · 06-19-2012, 06:39 PM

Take the seat off and anything that will keep it from laying upside down unevenly (rod holder mounts etc).

Put some blankets, towels or drop cloths on the Driveway or Garage floor on the ends and then Flip it completely upside down so it sits "On an even keel" & then Wet sand the deep gouges with 800-1000 grit emery cloth then rinse well so you can get any grit out that got embedded in the plastic.

Make sure you have got good light and no wind or breeze and then break out a hand held propane torch (home depot, lowes or true value or even harbor freight has them).

Start very lightly keeping a good distance from what you want to smooth out and Slowly work the flame closer to the hull. Focus on the distance from the tip of the torch and watch the color of the flame and the sheen of the area around the flames contact area on the plastic.

As you go take the time to change you angles of view on the area you are working on and shift the light if you are using a drop light. ...You do not want any excessive smoke!.

It's all about being methodical & slow but be Very, Very Carefull!!!

So you do not burn a hole through it!

With a little practice and a gentile touch you can make any Plastic hulled Kayak shine like a Diamond in a Goats Ass using a hand held propane torch

Cbad Mike · 06-20-2012, 12:07 PM

Interesting thought using a torch but if I myself was going to do that I would use a flame spreading nozzle. I think that using one would would give a more even finish while lessening the chance of burning the plastic. Thats my 2 cents.

tacmik · 06-20-2012, 05:09 PM

Has anyone ever tried a hair blower? Just a thought.

T-Rex · 06-20-2012, 07:00 PM

I've used my heat gun several times and it works pretty good for smoothing out rough areas and bring back the gloss. Easier to use, but not as fast as a propane torch.

I don't think a hair dryer will get hot enough to be effective.

sandsquirt · 06-21-2012, 09:09 PM

They make a product called Plastic Renew for motorcycle/atv fenders. I imagine that it would work well on kayaks.

mtnbykr2 · 06-22-2012, 07:27 AM

Quote:

Originally Posted by sandsquirt

They make a product called Plastic Renew for motorcycle/atv fenders. I imagine that it would work well on kayaks.

that's a great idea, I may try that out...thanks

echo1er · 06-22-2012, 07:43 AM

Quote:

Originally Posted by T-Rex

I've used my heat gun several times and it works pretty good for smoothing out rough areas and bring back the gloss. Easier to use, but not as fast as a propane torch.

I don't think a hair dryer will get hot enough to be effective.

http://www.youtube.com/watch?v=SKxpM7CVY-4

cabojohn · 06-22-2012, 11:40 AM

Quote:

Originally Posted by Drake

The only reason I want to clean it up is to sell it. I don't want to sell it looking like it fell off my truck

Wash the kayak good and then use Armor All top and bottom. Wipe it down good.

06-19-2012, 10:46 AM	#1
Drake Guest Posts: n/a	Polishing Hull of Proangler My PA is pretty scratched up from the previous owner. I was wondering if there was a good way to polish it up and make it look better. I was thinking of either using a rubbing compound/polishing compound combo or lightly lightly lightly wetsanding it with really fine sand paper. If it gets a matte look to it that way I'm totally ok with that. I just don't want to thin the hull anymore than I have to. Thanks

06-19-2012, 11:08 AM	#2
MrM Senior Member Join Date: May 2012 Location: The Matrix Posts: 643	Interesting post... I would love to hear if anyone has info on this. I've got a scratch or two from beach landings I'd like to fill in and smooth out. __________________ -Kevin

06-19-2012, 11:46 AM	#3
mrJB Senior Member Join Date: Feb 2007 Location: O.C. Posts: 352	Polyethylene will buff and/or sand out to a certain extent, just a lot of work and will never get a supershine. It will only get the very lightest scratches. You can get somewhat deeper scratches by scraping, either with a cabinet scraper or razor blade, but then you are taking off some material. I've done it - scraped, wet sanded, buffed with a buffer, on and on. Just depends on how much work you want to put into it. A heat gun will put some shine back into it but there are potential risks... My $.02, clean it up, put some sacrificial tape strips on the wear area, and use some plastic protectant on it Try to keep it nice from this point on and wash it down after every outing... __________________ "I Brake for Halibut"

06-19-2012, 11:51 AM	#4
mtnbykr2 Senior Member Join Date: Sep 2009 Location: newbury park ca Posts: 2,323	"battle scars" __________________

06-20-2012, 05:09 PM	#9
tacmik Senior Member Join Date: Jun 2007 Location: East County Posts: 914	Has anyone ever tried a hair blower? Just a thought. __________________

06-19-2012, 12:51 PM	#5
Drake Guest Posts: n/a	The only reason I want to clean it up is to sell it. I don't want to sell it looking like it fell off my truck

06-19-2012, 06:39 PM	#7
Chief Gunner Member Join Date: May 2012 Location: Lakeside Posts: 97	Take the seat off and anything that will keep it from laying upside down unevenly (rod holder mounts etc). Put some blankets, towels or drop cloths on the Driveway or Garage floor on the ends and then Flip it completely upside down so it sits "On an even keel" & then Wet sand the deep gouges with 800-1000 grit emery cloth then rinse well so you can get any grit out that got embedded in the plastic. Make sure you have got good light and no wind or breeze and then break out a hand held propane torch (home depot, lowes or true value or even harbor freight has them). Start very lightly keeping a good distance from what you want to smooth out and Slowly work the flame closer to the hull. Focus on the distance from the tip of the torch and watch the color of the flame and the sheen of the area around the flames contact area on the plastic. As you go take the time to change you angles of view on the area you are working on and shift the light if you are using a drop light. ...You do not want any excessive smoke!. It's all about being methodical & slow but be Very, Very Carefull!!! So you do not burn a hole through it! With a little practice and a gentile touch you can make any Plastic hulled Kayak shine like a Diamond in a Goats Ass using a hand held propane torch

06-20-2012, 12:07 PM	#8
Cbad Mike Senior Member Join Date: Apr 2012 Location: Carlsbad Ca. Posts: 1,206	Interesting thought using a torch but if I myself was going to do that I would use a flame spreading nozzle. I think that using one would would give a more even finish while lessening the chance of burning the plastic. Thats my 2 cents.

06-20-2012, 07:00 PM	#10
T-Rex Senior Member Join Date: Mar 2005 Location: Rancho Santa Margarita Posts: 770	I've used my heat gun several times and it works pretty good for smoothing out rough areas and bring back the gloss. Easier to use, but not as fast as a propane torch. I don't think a hair dryer will get hot enough to be effective. __________________

06-21-2012, 09:09 PM	#11
sandsquirt Junior Join Date: Jun 2011 Posts: 9	They make a product called Plastic Renew for motorcycle/atv fenders. I imagine that it would work well on kayaks.