|
|
|
07-08-2014, 01:28 PM
|
#1 |
|
Member
Join Date: Apr 2008
Location: Santa Barbara
Posts: 59
|
Hobie Wheels
Wife has an old Hobie Outback Mirage Hank Parker. She has the old plastic wheels that she wants to install while kayak is on the Rack and Roll trailer. Wheel posts are a loose fit in the scupper holes and wheels fall out. Is there a kit available to pin the wheel posts above the scupper hole to hold wheels in place? I could drill a hole through the post and add a cotter pin but thought there might be a cleaner fix. bosco
|
|
|
|
07-08-2014, 01:55 PM
|
#2 |
|
Brandon
Join Date: Jul 2011
Location: San Diego
Posts: 2,345
|
My set of hobie wheels have a plastic cap on one post connected to bungie and a hole already drilled. Do yours not?
Sent from my iPhone using Tapatalk |
|
|
|
|
07-08-2014, 02:52 PM
|
#3 |
|
Senior Member
Join Date: Mar 2011
Location: Santa Ana/Westminster
Posts: 1,256
|
Newer wheels had a retaining pin.
__________________
Kevin Yellow PA12 |
|
|
|
|
07-08-2014, 02:57 PM
|
#4 |
|
Member
Join Date: Apr 2008
Location: Santa Barbara
Posts: 59
|
Hobie Wheels
These wheels do not have plastic caps or retaining pins. Tops of posts are square cut and open. bosco
|
|
|
|
|
07-08-2014, 03:15 PM
|
#5 |
|
Senior Member
Join Date: Mar 2011
Location: Santa Ana/Westminster
Posts: 1,256
|
DiY a retaining pin; as long as the post are long enough it should be easy.
__________________
Kevin Yellow PA12 |
|
|
|
|
07-09-2014, 08:06 PM
|
#6 | |
|
Senior Member
Join Date: Mar 2011
Location: Nor Cal...30 min from Bodega/Tomales Bay, 1hr from Clear Lake, 2+ hr to Berryessa & the Delta
Posts: 729
|
Quote:
 Just my .02. FFY |
|
|
|
|
|
07-09-2014, 08:23 PM
|
#7 |
|
Senior Member
Join Date: Aug 2011
Location: West Covina, CA
Posts: 434
|
DIY interchangeable/adjustable Hobie wheels
I just finish the mods and upgrade on my DIY PA14 cart. It's super stable and capable of handling 200lbs capacity. It's still adjustable for different size scupper holes and can swap to beach wheels if needed; with a 30" wheel base.
Next mod is to add those pins to hold it in place when it's plug into the scupper holes. Also some rubber pipe tubing on the support to prevent bottom surface scratch. |
|
|
|
|
07-09-2014, 08:44 PM
|
#8 |
|
Senior Member
Join Date: Aug 2011
Location: West Covina, CA
Posts: 434
|
maybe you need something like this
 Or this 
|
|
|
|
|
07-09-2014, 08:46 PM
|
#9 |
|
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
So you finally finished building your wheels.... Great!
Now you can finally go down to OEX and buy youself some of these. 
__________________
There's nothing colder than yesterday's hotdog. |
|
|
|
|
07-09-2014, 09:30 PM
|
#10 | |
|
Senior Member
Join Date: Aug 2011
Location: West Covina, CA
Posts: 434
|
Quote:
 , also I have the hobie beach wheel version too and I'm not satisfied with that too.
|
|
|
|
|
|
07-09-2014, 09:42 PM
|
#11 |
|
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
Did you get the crossbars for the cart like you were supposed to?
How was the cart not cutting it? Ive been using it for the past 3-4 years and it works great.
__________________
There's nothing colder than yesterday's hotdog. |
|
|
|
|
07-09-2014, 11:35 PM
|
#12 |
|
Senior Member
Join Date: Jun 2013
Posts: 273
|
Any link to these crossbars thanks
Sent from my iPhone using Tapatalk |
|
|
|
|
07-10-2014, 12:12 AM
|
#13 |
|
Senior Member
Join Date: Aug 2011
Location: West Covina, CA
Posts: 434
|
Take a picture of the setup. Didn't know you needed a cross bar.
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
