10-16-2011, 08:02 PM | #1 |
Scoot
Join Date: Aug 2005
Location: Menifee
Posts: 164
|
Leaky boat?
|
10-16-2011, 08:16 PM | #2 |
Currently @ MLO Territory
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
|
Put some foam on the bottom and fill her inside with water till she blows
__________________
Team: Disbanded You only have one chance in this life...make the right decision(s)...so you don't regret it
|
10-16-2011, 08:24 PM | #3 |
Member
Join Date: Jun 2007
Posts: 53
|
talk to cj or andy at oex, they'll make it right. 86 the foam idea from Darknachos aka Wiredantz or whatever.
|
10-16-2011, 08:28 PM | #4 | |
Currently @ MLO Territory
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
|
Quote:
That was the true Mexican way...Lol
__________________
Team: Disbanded You only have one chance in this life...make the right decision(s)...so you don't regret it
|
|
10-16-2011, 08:38 PM | #5 |
Member
Join Date: Jun 2007
Posts: 53
|
One option is to fill the yak with water and see where it leaks, another is to spray the yak with a soap water mixture, use a shop vac to blow air into the yak and find out where the leak is coming from.
|
10-16-2011, 10:14 PM | #6 |
Senior Member
Join Date: Mar 2009
Posts: 2,384
|
If your yak has rivets, it has leaks. If it leaks a lot you can probably just roll around a few gallons of water inside to find the trouble area. Scuppers are the biggest culprits. Try plugging them from the bottom and filling the foot and bait wells with water to check them.
|
10-17-2011, 09:45 AM | #7 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
|
First thing I do is inspect the entire hull, looking for obvious cracks. Next I test the scuppers as Greg said. If all else fails, I put 5-10 gallons inside and tip the boat at different angles to find the culprit.
__________________
|
10-18-2011, 03:55 PM | #8 |
Scoot
Join Date: Aug 2005
Location: Menifee
Posts: 164
|
Thanks...
for the ideas, nothing obvious but the boat is 10+ years old! i'm guessin scupper holes.
|
10-18-2011, 04:00 PM | #9 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
|
Usually scupper pin holes are there right out of production. You can get cracks in them over time from the stress applied with your tie downs. Never run tie downs through the scuppers and never use ratcheting tie downs, they apply to much force.
__________________
|
10-18-2011, 04:06 PM | #10 |
Currently @ MLO Territory
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
|
I always run my tie downs through the scuppers!!!!! That how i keep the kayak from flying off when i am drving 90mph. !!!! Andy, What is the proper method of tying the kayak down so it doesn't fly off?
__________________
Team: Disbanded You only have one chance in this life...make the right decision(s)...so you don't regret it
|
10-18-2011, 04:43 PM | #11 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
|
Frank your kayak is tapered at each end, with 2 tie downs holding it in place it can't go anywhere.
Just make sure it is snug and not able to move side to side, then tie a knot in the tag end to keep it from backing out on the clasp. I don't go 90, but 80 no problem.
__________________
|
10-18-2011, 04:46 PM | #12 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
|
trust me
__________________
|
10-18-2011, 05:13 PM | #13 |
Currently @ MLO Territory
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
|
Thanks Andy, you saved my life.
I would of sunk to my death one of these days because of my scupper holes.
__________________
Team: Disbanded You only have one chance in this life...make the right decision(s)...so you don't regret it
|
10-18-2011, 05:26 PM | #14 |
Senior Member
Join Date: Sep 2009
Location: newbury park ca
Posts: 2,323
|
|
10-19-2011, 12:16 AM | #15 |
Junior
Join Date: Oct 2011
Location: Scranton
Posts: 1
|
A quick way to check (its been in my leaks were) is to use scupper plugs to plug the bottom ... just do not add too far. Then fill the water ruin and look inside the boat leaks. This means that you can see the scuppers. I'm getting a Hobie again this week, hopefully, before leaving the store I will spray the hatches of the ships and check all the scuppers.
Good luck. silk greenery |
10-19-2011, 12:43 AM | #16 |
Senior Member
Join Date: May 2011
Location: SD
Posts: 216
|
Looks Like a big Truck Full of Hobies.....
Santa.... Please bring me one of Andy's Trucks full of yaks for christmas, a new VHF radio for George... a fish finder for Sharon, a new shoulder for Wade, a new pair of shorts for stinkymatt, a bag of gold for Yakmedic, a delicious bagel sandwich for Gcasher, a case of bananas for Darkhorse, and 5 new shinny surface irons for the Kid..... To be Continued............. T . . . . . T |
10-19-2011, 09:16 AM | #17 | |
Junior
Join Date: Sep 2008
Location: San Diego, CA
Posts: 27
|
Quote:
Funny Travis, That 5 cases of Bananas just made me blow my breakfast burrito out my nose. Thanks |
|
10-19-2011, 10:21 AM | #18 |
Senior Member
Join Date: Apr 2010
Posts: 6,856
|
__________________
www.facebook.com/Teamsewer |
10-19-2011, 10:25 AM | #19 |
Senior Member
Join Date: Feb 2011
Location: Wrightwood
Posts: 623
|
Very funny Travis
|
10-19-2011, 10:43 AM | #20 | |
Senior Member
Join Date: Apr 2010
Posts: 6,856
|
Quote:
Don't forget a 10+lb halibut for Roby. Since he needs it asap can santa bring it before october is over?
__________________
www.facebook.com/Teamsewer |
|
|
|