Lowrance Transducer Scupper Mount - Kayak Fishing Adventures on Big Water’s Edge

HELLSTER INC. · 08-26-2012, 06:04 PM

Just finished mounting a Lowrance Elite-4x DSI Sonar on my malibu x-13 yak using the new Lowrance Transducer Scupper Mount. Had to trim a few piece's but it worked out rather well. I think the price of the kit from lowrance is rather expensive but it really makes it easy and a very clean install. By trimming a few piece's it sits tight in groove under yak. Beach landings should not be a problem if your careful.

HELLSTER INC. · 08-26-2012, 06:09 PM

Before anyone asks, it was mounted in the second hole so the transducer is more protected. Mounted in the first hole it hung down an extra 1/2 inch. The nice thing is it can be removed and remounted as needed.

echo1er · 08-26-2012, 06:48 PM

so... using DSI you must go through the Scuffer?

HELLSTER INC. · 08-26-2012, 07:04 PM

DSI will not read properly or at all for that matter thru the hull!

echo1er · 08-26-2012, 08:27 PM

thanks for the quick reply

lowprofile · 08-26-2012, 09:39 PM

super clean. i might end up doing this but in the rear scupper.

08-26-2012, 06:04 PM	#1
HELLSTER INC. Senior Member Join Date: Jun 2008 Location: Banning, ca Posts: 429	Lowrance Transducer Scupper Mount Just finished mounting a Lowrance Elite-4x DSI Sonar on my malibu x-13 yak using the new Lowrance Transducer Scupper Mount. Had to trim a few piece's but it worked out rather well. I think the price of the kit from lowrance is rather expensive but it really makes it easy and a very clean install. By trimming a few piece's it sits tight in groove under yak. Beach landings should not be a problem if your careful. __________________ HELLSTER. 2015 Hobie PA 14 2016 Hobie Revo 13 2018 SeaFox 248 Commander

08-26-2012, 06:09 PM	#2
HELLSTER INC. Senior Member Join Date: Jun 2008 Location: Banning, ca Posts: 429	Before anyone asks, it was mounted in the second hole so the transducer is more protected. Mounted in the first hole it hung down an extra 1/2 inch. The nice thing is it can be removed and remounted as needed. __________________ HELLSTER. 2015 Hobie PA 14 2016 Hobie Revo 13 2018 SeaFox 248 Commander

08-26-2012, 07:04 PM	#4
HELLSTER INC. Senior Member Join Date: Jun 2008 Location: Banning, ca Posts: 429	DSI will not read properly or at all for that matter thru the hull! __________________ HELLSTER. 2015 Hobie PA 14 2016 Hobie Revo 13 2018 SeaFox 248 Commander

08-26-2012, 09:39 PM	#6
lowprofile #1 on fishstick's hitlist Join Date: May 2011 Location: Sea level Posts: 1,478	super clean. i might end up doing this but in the rear scupper. __________________ MLPA- My Largest Poaching Area

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

08-26-2012, 06:48 PM	#3
echo1er Senior Member Join Date: Sep 2011 Posts: 598	so... using DSI you must go through the Scuffer?

08-26-2012, 08:27 PM	#5
echo1er Senior Member Join Date: Sep 2011 Posts: 598	thanks for the quick reply