![]() |
|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Community | Calendar | Today's Posts | Search |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
MD 180 Broken Mast
Was out fishing this weekend and broke another mast, this time on my MD180. I always carry spare parts and tools with me but unfortunately since I upgraded to the newer style drive my spare parts don't fit the new drive minus the drive cables. In this case spare parts would have done me no good as the threaded portion of the mast snapped off inside the sprocket. On the older versions of the Mirage Drive you could just swap out the sprocket on the water with not too much difficulty. With the newer style drive you can't really do that. The correct way to fix this problem would be the warranty route, in that case I would have had to replace the entire spine, which includes the entire mechanism and sprockets and what not, and also waiting a couple of weeks to process. A couple weeks without my drive...? No... that will not do... So this is how I was able to fix it up! Here is the moment I confirmed my broken mast! DAMN! It's going to be a looooonnnng paddle back... ![]() Yep... ![]() So on the way home, I gave Andy a call at OEX Sunset Beach. I told him about my broken mast and asked if he had a replacement mast available....and he did! While I was there I noticed that the broken mast that came off of the drive was in fact not the correct turbo fin mast but was the standard size st mast, which is at least an 1.5 or 2"s, short. I bought the drive new with the turbo fins installed too. I guess it was a mix-up at the factory...In any case I walked out the door with 2 new masts and a new project. ![]() Broken fin removed from the drive. ![]() Here was the task at hand...1/2" of broken mast at the bottom of this hole. UGH! ![]() Here are the tools I used to get the broken mast out. And the procedure was to center punch the broken piece as close to center as possible...check. Start drilling with a smaller sized drill bit and drill thru the broken piece....check. Step up the size of the drill bit to fit the size of the easy out....check. Insert easy out into correct sized hole and back broken piece out. Check. ![]() Here it comes! ![]() Close up. ![]() Voila! ![]() New masts from Andy, screwed right into place! ![]() ![]() ![]() Back in Business! ![]() Thanks Andy for the spare parts, as you can see everything worked out just fine ![]()
__________________
There's nothing colder than yesterday's hotdog. |
![]() |
![]() |
![]() |
#2 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
Impressive wrenching! I have had to do similar on snapped bolts on my son's moto bike. Glad this ended up working. The wrong sized masts were a surprise. This was one of the very first 180 drives, it had come with a Pro Angler, before I could even order separate drives.
Diggin' the new light and flakey carpet kit!
__________________
![]() ![]() |
![]() |
![]() |
![]() |
#3 | |
Senior Member
Join Date: Apr 2015
Location: SD County
Posts: 360
|
Looks like
Quote:
|
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Jan 2012
Posts: 2,526
|
was failure result
of mast being shorter? or is this just one one the failures that comes with usage?
|
![]() |
![]() |
![]() |
#5 | |
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
Quote:
![]()
__________________
There's nothing colder than yesterday's hotdog. |
|
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Jun 2010
Location: Murrieta, CA and Bonney Lake, WA
Posts: 425
|
nice fish
How many others feel this way?
"A couple weeks without my drive...? No... that will not do..." Very resourceful! mad props! |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Jun 2014
Posts: 417
|
I doubt warranty would let you go "a couple weeks" without your drive. That being said, nice work getting that out. Screw extractors are a life saver and a must have in everyone's garage.
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Apr 2013
Location: Los Angeles
Posts: 1,884
|
Are the shafts stainless steel?
If so drilling SS is very difficult. Unless they are less grade of SS. Regardless, good job on repairs. |
![]() |
![]() |
![]() |
#9 | |
Senior Member
Join Date: Sep 2010
Location: South OC
Posts: 1,606
|
Quote:
Nice work Tony... working like a surgeon. |
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Jun 2014
Posts: 417
|
They are stainless but it can be drilled if done properly. Drilling stainless requires high pressure, low speed and lots of oil. If you overheat it, it will blue and break your bits.
|
![]() |
![]() |
![]() |
#11 |
Member
Join Date: Aug 2013
Location: Pine Valley when not fishing La Jolla
Posts: 2,641
|
Nice work Tony, drilling out a broken bolt or stud is not easy because it's hard to drill centered and large enough to use an easy out that will bite well and hold the amount of pressure needed. In this case it helps that it's in a brass bushing and not rusted in. Even though this is a good post on a possible weak area. I wish you had told us about the nice Hali on board. I think the broken mast is because that mast had a defect other wise it would not have broken in that spot and not had stretch signs on the metal post instead of a clean break.
__________________
MARK ......... 2016 MALIBU X FACTOR, 2020 SOLO SKIFF (Fishing Kayak on Steroids ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#12 |
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
The mast was pretty hard, but like Shane said low speed, and also taking your time to get your drill centered as close as possible really helps. Starting with a small bit and stepping it up to a larger bit several times takes time so you have to be patient. At least it wasn't as bad as an exhaust stud...compared to one of those this one was a piece of cake...
...another thing that made this project challenging, is that the broken piece was recessed back into the sprocket about an 1" or 1 1/2... Makes me wonder if Hobie were to score the mast an inch or so below the end of the sprocket to make a point where if the mast were to fail it would fail in a manner in which you could replace it without the use of special tools....Of course that would make a weak point...but that is the point...just a thought. It's alot cheaper replacing a mast as opposed to replacing complete spine assemblies...
__________________
There's nothing colder than yesterday's hotdog. |
![]() |
![]() |
![]() |
#13 | |
Senior Member
Join Date: Apr 2015
Location: SD County
Posts: 360
|
Flawed Part
Quote:
|
|
![]() |
![]() |
![]() |
#14 |
Made in U.S.A.
Join Date: Oct 2012
Location: Dana Point
Posts: 1,625
|
Or there is too much play between the mast and housing, or the housing flexes too much, and there isn't enough support past the threads. Or, Tony is just a beast.
__________________
Hobie PA 14 ¸.·´¯`·.´¯`·.¸¸.·´¯`·.¸><(((º> Jackson Kraken ¸.·´¯`·.¸.·´¯`·.´¯`·.¸¸.·´¯`·.¸><(((º> Malibu X-Factor ¸.·´¯`·.´¯`·.¸¸.·´¯`·.¸><(((º> Malibu Stealth-12 ¸.·´¯`·.´¯`·.¸¸.·´¯`·.¸><(((º> Its not a spelling B its a fishing B ![]() |
![]() |
![]() |
![]() |
#15 |
Senior Member
Join Date: Apr 2015
Location: SD County
Posts: 360
|
|
![]() |
![]() |
![]() |
#16 |
Senior Member
Join Date: Mar 2011
Location: Santa Ana/Westminster
Posts: 1,256
|
No covered under warranty?
__________________
Kevin Yellow PA12 |
![]() |
![]() |
![]() |
#17 | |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
Quote:
__________________
![]() ![]() Last edited by Iceman; 08-30-2017 at 01:50 PM. |
|
![]() |
![]() |
![]() |
#18 |
Emperor
Join Date: May 2009
Location: Buena Park
Posts: 3,649
|
Yes, Andy did supply me with the new masts. Hobie and Andy (OEX) have stepped up and taken care of me many times before, as well as all other Hobie owners.
...Good reason to buy your Hobie from OEX!
__________________
There's nothing colder than yesterday's hotdog. |
![]() |
![]() |
![]() |
#19 |
Senior Member
Join Date: Mar 2014
Location: The city of Orange
Posts: 1,278
|
|
![]() |
![]() |
![]() |
#20 |
Senior Member
Join Date: Apr 2013
Location: Los Angeles
Posts: 1,884
|
Andy runs a glass operation.
|
![]() |
![]() |
![]() |
|
|