One more dumb question about Spectra... - Kayak Fishing Adventures on Big Water’s Edge

BrokeLoser · 03-23-2011, 06:51 PM

I'm trying to figure out how much braid I need.
I've decided to back up 2 sealine 20's and 2 sealine 30's with 65#
Obviously, the line capacities printed on the reels are based on mono line.
How do I know how much braid these reels will hold so I know how big a spool to order. Someone has got to have this down to a science by now...huh...or is there a "braid chart" somewhere?

bus kid · 03-23-2011, 07:05 PM

I'm guessing 200 - 300 yrds should be good.

charkbait has the saltist listed as 400 yrds at 65 lbs of spectra. its mono cap is 270 yrds at 30.
the 20 sha is listed at 20/210 mono
the 30 sha is listed at 25/230 mono

http://www.charkbait.com/cs/csrd.htm

bubblehide · 03-23-2011, 07:10 PM

Actually that's a great question that many of us have struggled with. I'm not sure if other companies are doing this, but Avet now publishes line capacity of thier reels for both mono and braid; so when I have the same question, I refer to their published information (the relevant part), and use it extrapolate so I can reasonably approximate the amount of braid needed.

Hope that helps.

BrokeLoser · 03-23-2011, 07:18 PM

Quote:

Originally Posted by bubblehide

Actually that's a great question that many of us have struggled with. I'm not sure if other companies are doing this, but Avet now publishes line capacity of thier reels for both mono and braid; so when I have the same question, I refer to their published information (the relevant part), and use it extrapolate so I can reasonably approximate the amount of braid needed.

Hope that helps.

Hmmm..we may be on to something...Thanks for the tip

Regor · 03-23-2011, 07:18 PM

Here's some specs on a Curado 300

Line Capacity - Mono: 12/240, 14/190, 20/120
Line Capacity - Braid: 50/205, 65/120, 80/105

If you can't find a spec for your specific reel, find a reel with the same mono capacity that also shows the braid equivalent.

grey zone · 03-23-2011, 08:13 PM

I have 2 Avet JX reels filled to 3/16" from the edge of the spool with 50lb spectra and it takes aprox. 480 yds. of tightly packed spectra to bring them to this point. Pack your spectra very tight!

RedSledTeam · 03-23-2011, 09:14 PM

Quote:

Originally Posted by BrokeLoser

I'm trying to figure out how much braid I need.
I've decided to back up 2 sealine 20's and 2 sealine 30's with 65#
Obviously, the line capacities printed on the reels are based on mono line.
How do I know how much braid these reels will hold so I know how big a spool to order. Someone has got to have this down to a science by now...huh...or is there a "braid chart" somewhere?

How will PowerPro change the way I fish?
In addition to enhancing your enjoyment and increasing your catch, PowerPro slightly changes the way you set up for a day of fishing. PowerPro works great with any kind of reel, so you don't need any special equipment. Still, switching from mono to PowerPro is like trading your fly swatter in for a two-by-four: it takes a little care to get used to all that extra power!

So, check your reel capacity for the approximate mono equivalent (65# spectra = 16 lb mono and do the math: 300yds of 65# = ~300yds16# and vice-versa.

wiredantz · 03-23-2011, 09:27 PM

Thanks Red, ill keep this on my fav list.

bubblehide · 03-23-2011, 09:31 PM

Quote:

Originally Posted by RedSledTeam

...

So, check your reel capacity for the approximate mono equivalent (65# spectra = 16 lb mono and do the math: 300yds of 65# = ~300yds16# and vice-versa.

Even better!

BrokeLoser · 03-23-2011, 09:59 PM

I was almost embarrassed to start this thread. Glad I did.

maui jim · 03-24-2011, 07:32 AM

As I tell all my crews....No such thing as a dumb question....Just dumb answers...

grey zone · 03-24-2011, 09:03 AM

When you fill up a reel first chose what lb. spectra you want to use, 50 to 65lb is what I use. I hate to waste spectra so I usually buy less than my reel will hold. I like 300yd spools, this is a lot of line and not too expensive. Twenty years ago you could not put this much pulling power on a small reel. If 300yds does not fill your spool to the level you want it, build up your spool with some mono. I usually put at least a small amount of mono on any reel before I put spectra on. If you put spectra straight to an aluminim spool put a piece of masking tape on it to keep it from slipping.

If you have a lot of reels to fill a 1500yd spool might be a good investment. I keep telling myself to get one. If you end up with odd but usefull lengths of spectra save it and splice it somewhere. All my old spectra ends up as backing.

Billy V · 03-24-2011, 11:33 AM

A little know fact...

Most tackle shops have (short spools) of spectra in various Lb Test up on the shelves. They will sell you these spools cheap and you can do a triple surgeon end loop - a cats paw - and another triple surgeon to make a strong connection with other short spools. (Its basically a wind on connection with spectra to spectra)
There are other knots that will work as well.

I've tied it for a few people when they were on a budget.

03-23-2011, 06:51 PM	#1
BrokeLoser Senior Member Join Date: Feb 2011 Location: Corona, CA Posts: 472	One more dumb question about Spectra... I'm trying to figure out how much braid I need. I've decided to back up 2 sealine 20's and 2 sealine 30's with 65# Obviously, the line capacities printed on the reels are based on mono line. How do I know how much braid these reels will hold so I know how big a spool to order. Someone has got to have this down to a science by now...huh...or is there a "braid chart" somewhere?

03-23-2011, 07:05 PM	#2
bus kid Team Keine Zugehörigkeit Join Date: Nov 2010 Location: Way out there Posts: 2,854	I'm guessing 200 - 300 yrds should be good. charkbait has the saltist listed as 400 yrds at 65 lbs of spectra. its mono cap is 270 yrds at 30. the 20 sha is listed at 20/210 mono the 30 sha is listed at 25/230 mono http://www.charkbait.com/cs/csrd.htm __________________ Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ Last edited by bus kid; 03-23-2011 at 07:38 PM.

03-24-2011, 07:32 AM	#11
maui jim Senior Member Join Date: May 2010 Location: Cypress, CA Posts: 789	As I tell all my crews....No such thing as a dumb question....Just dumb answers... __________________

03-24-2011, 11:33 AM	#13
Billy V Senior Member Join Date: Sep 2006 Location: Bay Ho Posts: 1,382	A little know fact... Most tackle shops have (short spools) of spectra in various Lb Test up on the shelves. They will sell you these spools cheap and you can do a triple surgeon end loop - a cats paw - and another triple surgeon to make a strong connection with other short spools. (Its basically a wind on connection with spectra to spectra) There are other knots that will work as well. I've tied it for a few people when they were on a budget. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-23-2011, 07:10 PM	#3
bubblehide Senior Member Join Date: Jun 2008 Posts: 552	Actually that's a great question that many of us have struggled with. I'm not sure if other companies are doing this, but Avet now publishes line capacity of thier reels for both mono and braid; so when I have the same question, I refer to their published information (the relevant part), and use it extrapolate so I can reasonably approximate the amount of braid needed. Hope that helps.

03-23-2011, 07:18 PM	#5
Regor Greg Join Date: May 2010 Location: Chula Vista, ca Posts: 509	Here's some specs on a Curado 300 Line Capacity - Mono: 12/240, 14/190, 20/120 Line Capacity - Braid: 50/205, 65/120, 80/105 If you can't find a spec for your specific reel, find a reel with the same mono capacity that also shows the braid equivalent.

03-23-2011, 08:13 PM	#6
grey zone Senior Member Join Date: Mar 2005 Location: san diego Posts: 158	I have 2 Avet JX reels filled to 3/16" from the edge of the spool with 50lb spectra and it takes aprox. 480 yds. of tightly packed spectra to bring them to this point. Pack your spectra very tight!

03-23-2011, 09:27 PM	#8
wiredantz Currently @ MLO Territory Join Date: Dec 2010 Location: Under the Shadow Posts: 2,290	Thanks Red, ill keep this on my fav list.

03-23-2011, 09:59 PM	#10
BrokeLoser Senior Member Join Date: Feb 2011 Location: Corona, CA Posts: 472	I was almost embarrassed to start this thread. Glad I did.

03-24-2011, 09:03 AM	#12
grey zone Senior Member Join Date: Mar 2005 Location: san diego Posts: 158	When you fill up a reel first chose what lb. spectra you want to use, 50 to 65lb is what I use. I hate to waste spectra so I usually buy less than my reel will hold. I like 300yd spools, this is a lot of line and not too expensive. Twenty years ago you could not put this much pulling power on a small reel. If 300yds does not fill your spool to the level you want it, build up your spool with some mono. I usually put at least a small amount of mono on any reel before I put spectra on. If you put spectra straight to an aluminim spool put a piece of masking tape on it to keep it from slipping. If you have a lot of reels to fill a 1500yd spool might be a good investment. I keep telling myself to get one. If you end up with odd but usefull lengths of spectra save it and splice it somewhere. All my old spectra ends up as backing.