How do you Attach your battery boxs in your kayak? - Kayak Fishing Adventures on Big Water’s Edge

Adam12 · 07-08-2010, 07:02 PM

http://www.bigwatersedge.com/bwevb/s...?t=6394&page=3

See post #55

kareem korn · 07-08-2010, 07:14 PM

Truthfully, I attatch the leads, roll it up in a dry bad and let it set in the hull, or sometimes the milk crate. Never had a problem.

Nic D · 07-08-2010, 07:19 PM

Quote:

Originally Posted by kareem korn

Truthfully, I attatch the leads, roll it up in a dry bad and let it set in the hull, or sometimes the milk crate. Never had a problem.

this is what I do as well

rrdstarr · 07-09-2010, 01:45 AM

You might be able to get this from OK. It is suspended in front of the forward hatch at four points.

cjthomas · 07-09-2010, 10:41 AM

velcro works the best.

Hunters Pa · 07-09-2010, 11:05 AM

Quote:

Originally Posted by kareem korn

Truthfully, I attatch the leads, roll it up in a dry bad and let it set in the hull, or sometimes the milk crate. Never had a problem.

Yep, works for me as well. My bait tank has a spot for the battery that runs it

KirkG. · 07-09-2010, 12:37 PM

I just bought some sticky backed velcro from wal-mart and after scuffing the inside bottom of the front hatch and bottom of the battery box just stuck it to the boat. Works good so far, hasnt come loose or moved around at all in the 6 months that its been mounted. I can take the battery out for charging without removing the box.

KirkG

Gino · 07-09-2010, 01:48 PM

Thanks for the inputs, I kinda like the Velcro idea. I will probebely go that rout, I like the OK battery bag, Ill have to see if I can get one. I have a Malibu Extreme, So ill have to rig it the same way.

dsafety · 07-09-2010, 02:51 PM

Velcro usually works if you can get it to stick and your battery is fairly small. If you want a more robust method consider strapping the battery in a box to the hull.

I wanted my battery box to be raised off the bottom of the hull which is usually a little wet. I took some foam pipe insulation, spread it out and glued it to two edges of the bottom of the battery box. That gave me the lift and provided a little cushioning.

Next I gooped some pad eyes to the hull. After the goop had cured, I ran a webbing strap through the pad eyes. The strap, ($2 at REI), has a quick disconnect buckle.

When I am ready to hit the water, I set the battery box in its place connect the buckle and cinch everything tight. I use a two-wire trailer light plug to attach the battery to the internal wiring in the hull.

This has worked better for me than Velcro which was always coming loose. This is probably because I have a fairly heavy 7AH battery that is too much for the Velcro to hold.

Bob

CurtyL · 07-09-2010, 03:56 PM

beware "marine velcro." there is not a brand out there that can stand up to a single trip on a yak with soething as heavy as a battery on deck. buy the waterproof box at OEX and tie a line to it.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

07-08-2010, 07:02 PM	#1
Adam12 Senior Member Join Date: Nov 2008 Location: Whittier Posts: 126	http://www.bigwatersedge.com/bwevb/s...?t=6394&page=3 See post #55

07-08-2010, 07:14 PM	#2
kareem korn Senior Member Join Date: May 2006 Location: C-bad Posts: 431	Truthfully, I attatch the leads, roll it up in a dry bad and let it set in the hull, or sometimes the milk crate. Never had a problem.

07-09-2010, 10:41 AM	#5
cjthomas Senior Member Join Date: Jun 2009 Posts: 108	velcro works the best.

07-09-2010, 12:37 PM	#7
KirkG. Member Join Date: Mar 2010 Location: Temecula Posts: 43	I just bought some sticky backed velcro from wal-mart and after scuffing the inside bottom of the front hatch and bottom of the battery box just stuck it to the boat. Works good so far, hasnt come loose or moved around at all in the 6 months that its been mounted. I can take the battery out for charging without removing the box. KirkG

07-09-2010, 01:48 PM	#8
Gino Senior Member Join Date: Mar 2009 Posts: 520	Thanks for the inputs, I kinda like the Velcro idea. I will probebely go that rout, I like the OK battery bag, Ill have to see if I can get one. I have a Malibu Extreme, So ill have to rig it the same way.

07-09-2010, 02:51 PM	#9
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,122	Velcro usually works if you can get it to stick and your battery is fairly small. If you want a more robust method consider strapping the battery in a box to the hull. I wanted my battery box to be raised off the bottom of the hull which is usually a little wet. I took some foam pipe insulation, spread it out and glued it to two edges of the bottom of the battery box. That gave me the lift and provided a little cushioning. Next I gooped some pad eyes to the hull. After the goop had cured, I ran a webbing strap through the pad eyes. The strap, ($2 at REI), has a quick disconnect buckle. When I am ready to hit the water, I set the battery box in its place connect the buckle and cinch everything tight. I use a two-wire trailer light plug to attach the battery to the internal wiring in the hull. This has worked better for me than Velcro which was always coming loose. This is probably because I have a fairly heavy 7AH battery that is too much for the Velcro to hold. Bob

07-09-2010, 03:56 PM	#10
CurtyL Senior Member Join Date: May 2009 Location: wherever the college girlz r Posts: 127	beware "marine velcro." there is not a brand out there that can stand up to a single trip on a yak with soething as heavy as a battery on deck. buy the waterproof box at OEX and tie a line to it.