![]() |
|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Commercial Fisherman
Join Date: May 2018
Location: La Jolla
Posts: 18
|
HELP FROM A KNOWLEDGEABLE BOATER
I’m looking to pick up a good sized aluminum that is in an interesting condition. I don’t want to discuss the details because I’m always concerned someone will undercut me, but I need some help. It’s here locally(SD area) and I can pick you up and drive you to come with me, I’d even give you like 5$, I just need some advice because this is my first vessel, and I don’t know all that much! Thanks so much, if you guys know anyone or can do it yourselves, PM me here. Thanks guys! |
![]() |
![]() |
![]() |
#2 |
Baitless on Baja
Join Date: May 2013
Location: Vista California, Gonzaga, San Quintin, Asuncion, Mag Bay
Posts: 4,250
|
Welded aluminum only. Best advice is to get a marine surveyor to check it out if it is in the water. On a trailer you need to water test. Good luck with your find.
__________________
http://www.mako-ville.com Home 760-630-4470 Cell 760-520-2514 YES YOU CAN |
![]() |
![]() |
![]() |
#3 | |
Senior Member
Join Date: May 2016
Location: SANTUCKET
Posts: 629
|
$5
Quote:
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Sorry had to. LOL GL Bud. |
|
![]() |
![]() |
![]() |
#4 |
Commercial Fisherman
Join Date: May 2018
Location: La Jolla
Posts: 18
|
Thanks makobob, yeah definitely welded hull and galvanized trailer. I am curious about the condition of the outboard and the hull. Also, I want to make sure that the electronics and steering are still in shape. Will likely need an overhaul.
|
![]() |
![]() |
![]() |
#5 | |
Senior Member
Join Date: May 2015
Posts: 571
|
Quote:
As far as the hull, a sea trial should tell you if any of the welds need fixing or leak. Engine - Only way to really get an idea of engine health is to do a compression test on the motor and match the reading to the acceptable compression recommended by the engine manufacturer. Also good maintenance records are crucial as well as general sound on the water. Look up the recommended service intervals and make sure the service has been done by the previous owner preferably at a shop or by a boat mechanic. During a seatrial you should really run the boat in all conditions and really give it some throttle- it should sound like it runs well. Stick to fuel injected if you don't want to tinker with carburetors and 4stroke if you don't want to worry about mixing oil into the fuel every time and a noisy motor. Check the trim controls. up down on the console and the motor if it has the buttons on the motor. Don't know much about steering, but my understanding of hydraulic systems is just need to make sure it doesn't leek (that includes rubber seals). Electronics: 1 do they work? 2 are they corroded? 3 do they look waterproof/wired for salt. TEST EVERYTHING under the conditions you will be using it. It's amazing how many little things you figure out later. bait tank plumping issues, bilge pump issues. Good Luck!
__________________
2018 Hobie Outback 13 I do not fear the storm as it will teach me how to sail my ship. |
|
![]() |
![]() |
![]() |
#6 |
Member
|
Watch out for Electrolysis. If you steel anything connected to the aluminum
![]() ![]() Good luck Steve |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Apr 2010
Posts: 6,855
|
When I purchased my boat I hired a marine surveyor to inspect the boat, he checked all controls, the batteries, electronics, etc, etc, he also checked the humidity levels on the hull……it was a cheap price to pay for professional advice. In the 5 years or so that I owned the boat I never had any major issues with it, other than wear and tear the only time that I had to take it to a shop was when a weld broke on the shift arm, other than that it was fine for the years that I had it.
Over the years I did manage to do many and I mean many upgrades to my boat, I knew my boat better than I knew my wife. Personally, I don’t think boats are meant for people that are not hands on or are not mechanically inclined; I changed impellers, ripped out every single wire and upgraded my entire electrical system, I installed my own electronics, I changed leaf springs, upgraded by brake system to disk brakes, etc, etc. Anyway, back to your question…………hire someone or bring someone with you that has some knowledge. Ask to take the boat on a test drive (offer to pay for some of the fuel) and put the boat through the ringer because once it’s yours it’s your problem.
__________________
![]() www.facebook.com/Teamsewer |
![]() |
![]() |
![]() |
#8 |
Commercial Fisherman
Join Date: May 2018
Location: La Jolla
Posts: 18
|
Thanks for the responses everyone, aside from patronizing remarks. I appreciate the thought out comments that a few of you addressed towards me, I'll post a pic if I purchase the vessel!
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Feb 2015
Location: Seattle Area
Posts: 861
|
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Jun 2005
Location: Grants Pass, OR
Posts: 1,903
|
Kenny's had his BWE welcome, he knows what he's talking about
![]()
__________________
Amish Ed You can't catch it again if it's dead! |
![]() |
![]() |
![]() |
#11 | |
Senior Member
Join Date: Apr 2011
Location: Menifee, CA
Posts: 1,468
|
Quote:
As for the electronics, it is very easy to rewire the boat if necessary. Look for green corrosion on the terminals, or rusted out terminals. Hull, should be easy to check that, it's usually open. Look for weld spots that appear to be patches. And definitely take it out first. The engine is where the money can stack up for repairs. Is it a two or four stroke? I prefer the four strokes myself, better gas mileage and less smoke. Look for corroded areas around the head and spark plug, check the rubber hoses. And try it out. If you're really set on the boat and see any discrepancies you can use that to possibly weasel the price down. I rebuilt a little fourteen footer before the CC, put a through hull live well on it. It was a sweet boat.
__________________
So long and thanks for all the fish... |
|
![]() |
![]() |
![]() |
#12 |
Señor member
Join Date: Mar 2005
Location: San Diego, CA
Posts: 1,627
|
Ditch the Aluminum idea, and look for a used livingston and re-power it. There I said it.
![]() |
![]() |
![]() |
![]() |
#13 |
.......
Join Date: Jan 2009
Posts: 1,509
|
I know a bit about aluminum boats. Feel free to PM me.
![]() |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|