magnetic fish finder mounts for transducer - Kayak Fishing Adventures on Big Water’s Edge

yak-fishing-socal · 04-17-2015, 05:29 AM

https://youtu.be/tAzy5mLXhBc
Here is another one...I'm going to try and make one similar Out of moldable plastic. Should be pretty easy with this stuff and some strong magnets
https://youtu.be/IhVuc6RNyaw
Iv just been putting off buying the InstaMorph

Just order the moldable plastic I'll make an new post when I make it..

straightrod · 04-17-2015, 07:40 AM

Neodymium magnets are strong. I don't know how they hold up to salt water.

AirborneYak · 04-17-2015, 10:19 AM

Quote:

Originally Posted by yak-fishing-socal

https://youtu.be/tAzy5mLXhBc
Here is another one...I'm going to try and make one similar Out of moldable plastic. Should be pretty easy with this stuff and some strong magnets
https://youtu.be/IhVuc6RNyaw
Iv just been putting off buying the InstaMorph

Let me know how you like if you get it.

bmercury · 04-18-2015, 10:11 PM

I have been considering this, but with the free time I have I will probably just drop my kayak off to have my new FF set up however it is done at the shop.

taggermike · 04-19-2015, 07:10 AM

Looks like simple time saving solution. No holes needed and if you have several kayaks it would take just seconds to swap the off over. The mount does show a decent profile and distance from the hull so maybe launching could be an issue and kelp would be a serious drag, literally. I was picturing the something dropping down off the bottom of the yak. But the video shows it mounted on the side. Good idea. If the inner mount was strapped on all you'd have to do is set the outside mount and go. And if you needed to clear kelp just reach over the side a few inches. Great idea. Mike

Murray · 10-06-2015, 03:55 PM

anyone get one of these? wondering if the side mount gets the transducer deep enough so splash bubbles do not interfere.

04-17-2015, 05:29 AM	#1
yak-fishing-socal kayak fishing socal Join Date: Nov 2013 Location: Southern California / Whittier Posts: 438	https://youtu.be/tAzy5mLXhBc Here is another one...I'm going to try and make one similar Out of moldable plastic. Should be pretty easy with this stuff and some strong magnets https://youtu.be/IhVuc6RNyaw Iv just been putting off buying the InstaMorph Just order the moldable plastic I'll make an new post when I make it.. Last edited by yak-fishing-socal; 04-19-2015 at 03:31 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

04-17-2015, 07:40 AM	#2
straightrod Member Join Date: Mar 2014 Posts: 48	Neodymium magnets are strong. I don't know how they hold up to salt water.

04-18-2015, 10:11 PM	#4
bmercury Senior Member Join Date: Sep 2010 Location: San Diego, CA Posts: 103	I have been considering this, but with the free time I have I will probably just drop my kayak off to have my new FF set up however it is done at the shop.

04-19-2015, 07:10 AM	#5
taggermike Senior Member Join Date: May 2007 Location: Chula Vista Posts: 1,589	Looks like simple time saving solution. No holes needed and if you have several kayaks it would take just seconds to swap the off over. The mount does show a decent profile and distance from the hull so maybe launching could be an issue and kelp would be a serious drag, literally. I was picturing the something dropping down off the bottom of the yak. But the video shows it mounted on the side. Good idea. If the inner mount was strapped on all you'd have to do is set the outside mount and go. And if you needed to clear kelp just reach over the side a few inches. Great idea. Mike

10-06-2015, 03:55 PM	#6
Murray Senior Member Join Date: Jul 2012 Location: Vista Posts: 326	anyone get one of these? wondering if the side mount gets the transducer deep enough so splash bubbles do not interfere.