Lowrance elite 4 hdi temp gauge issues - Kayak Fishing Adventures on Big Water’s Edge

Flyak13 · 05-13-2014, 04:13 PM

So I'm having an issue with the temp reading . It's reading 10-20 degrees over actual temperature.... This is my second transducer on this unit and I happend to me once before... I thought the first time because I had left it out in the sun but made sure to take extra care of this one.... I have a warranty but just don't want to be stuck with out a ff for who knows how long. Has anyone else experiences this ? How'd you fix the problem and what can I do to prevent this from happening again? Thanks

WildernessWanker · 05-13-2014, 05:15 PM

What are you doing before it happens? Because if you're peeing through a scupper hole ahead of the transducer... Otherwise I think the problem is with your connection into your unit.

Sent from my SPH-L520 using Tapatalk

Flyak13 · 05-13-2014, 05:31 PM

Lmao I'm definitely not peeing trough my scupper in front of my transducer.... So you think it could be corrosion or something in the connexrion?

WildernessWanker · 05-13-2014, 05:41 PM

How is your transducer mounted, if it's directly in the water that's one set of possible culprits however if it's a wetmount in the hull that's a different set of possible causes. Battery capacity and charge prior to issue?

Sent from my SPH-L520 using Tapatalk

jruiz · 05-13-2014, 06:15 PM

10 to 20 above is perfectly normal in the hull on a hot summer day

Flyak13 · 05-13-2014, 06:23 PM

It's mounted externally on my X factor where the factory Lowrance mount bracket is located. Battery is always freshly charged and was think that was the problem because I'm now learning I should be running a 12 amp batter and I have an 8 amp. But it was working perfectly for 3 trips when I replaced it and the old one worked fine for a about 5 trips till I left it outside turned over to dry out one afternoon

WildernessWanker · 05-13-2014, 07:02 PM

The amps won't cause issues besides change the length of time you can run it. This unit operates on a draw of .75 A so that only means an 8 amp battery will last a little over 10 hours whereas the 12 amp will last 16 hours. As long as you're running a 12 volt battery and it was charged prior to use then your connections are likely your culprit. Douse the connection points for the battery and FF with contact cleaner then apply dielectric grease, when you connect everything make sure it is nice and snug. Just my $0.02

Sent from my SPH-L520 using Tapatalk

Flyak13 · 05-13-2014, 07:16 PM

Thanks a bunch for your input and I'm definitely going to try that

05-13-2014, 04:13 PM	#1
Flyak13 Member Join Date: Mar 2014 Posts: 33	Lowrance elite 4 hdi temp gauge issues So I'm having an issue with the temp reading . It's reading 10-20 degrees over actual temperature.... This is my second transducer on this unit and I happend to me once before... I thought the first time because I had left it out in the sun but made sure to take extra care of this one.... I have a warranty but just don't want to be stuck with out a ff for who knows how long. Has anyone else experiences this ? How'd you fix the problem and what can I do to prevent this from happening again? Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-13-2014, 05:15 PM	#2
WildernessWanker WildernessWanker Join Date: Mar 2013 Location: Lancaster, CA Posts: 345	What are you doing before it happens? Because if you're peeing through a scupper hole ahead of the transducer... Otherwise I think the problem is with your connection into your unit. Sent from my SPH-L520 using Tapatalk

05-13-2014, 05:31 PM	#3
Flyak13 Member Join Date: Mar 2014 Posts: 33	Lmao I'm definitely not peeing trough my scupper in front of my transducer.... So you think it could be corrosion or something in the connexrion?

05-13-2014, 05:41 PM	#4
WildernessWanker WildernessWanker Join Date: Mar 2013 Location: Lancaster, CA Posts: 345	How is your transducer mounted, if it's directly in the water that's one set of possible culprits however if it's a wetmount in the hull that's a different set of possible causes. Battery capacity and charge prior to issue? Sent from my SPH-L520 using Tapatalk

05-13-2014, 06:15 PM	#5
jruiz Large Member Join Date: Jul 2012 Location: La Verne, CA Posts: 1,011	10 to 20 above is perfectly normal in the hull on a hot summer day

05-13-2014, 06:23 PM	#6
Flyak13 Member Join Date: Mar 2014 Posts: 33	It's mounted externally on my X factor where the factory Lowrance mount bracket is located. Battery is always freshly charged and was think that was the problem because I'm now learning I should be running a 12 amp batter and I have an 8 amp. But it was working perfectly for 3 trips when I replaced it and the old one worked fine for a about 5 trips till I left it outside turned over to dry out one afternoon

05-13-2014, 07:02 PM	#7
WildernessWanker WildernessWanker Join Date: Mar 2013 Location: Lancaster, CA Posts: 345	The amps won't cause issues besides change the length of time you can run it. This unit operates on a draw of .75 A so that only means an 8 amp battery will last a little over 10 hours whereas the 12 amp will last 16 hours. As long as you're running a 12 volt battery and it was charged prior to use then your connections are likely your culprit. Douse the connection points for the battery and FF with contact cleaner then apply dielectric grease, when you connect everything make sure it is nice and snug. Just my $0.02 Sent from my SPH-L520 using Tapatalk

05-13-2014, 07:16 PM	#8
Flyak13 Member Join Date: Mar 2014 Posts: 33	Thanks a bunch for your input and I'm definitely going to try that