solo skiff - Page 2 - Kayak Fishing Adventures on Big Water’s Edge

YakHanded · 02-15-2017, 08:37 AM

Super cool!

Here are some more videos
stability test:
https://www.youtube.com/watch?v=YYcBSvsgg4U

Through minor lj-esque 'surf':
https://www.youtube.com/watch?v=YD9x5WGUpo4

This is another company Hayaari Marine that makes a similar boat - pretty cool too:
https://www.youtube.com/watch?v=BbMSfUmoW2Y
https://www.youtube.com/watch?v=iA5mhRhnvIQ
https://www.youtube.com/watch?v=0-pEGUtvdw0

farreola · 02-15-2017, 09:10 AM

There are tons of videos on YouTube. There are is one where it is going through white caps, another through surf and a nice DYI dolly.

sandico · 02-15-2017, 09:24 AM

Yes we are going to be rigging up the Solo Skiff we have and bringing it to the shows. This is a unique kayak and has limitless rigging options. Unfortunately we will not be able to do any demo's until after the shows. Currently we are taking orders and they will be available in both OEX locations and come in 3 colors. Check it out here as well!

http://www.kayakfishingsupplies.com/...-skiff/id/288/

Kerry
OEX Mission Bay

SDROB · 02-15-2017, 09:42 AM

Quote:

Originally Posted by farreola

There are tons of videos on YouTube. There are is one where it is going through white caps, another through surf and a nice DYI dolly.

Buy one Frank! Or better yet 2, so I can borrow one

I can see us rolling to the islands.

Baja_Traveler · 02-15-2017, 05:24 PM

Exactly - this!!

When I get mine I want Bob to get busy with his drone!

For all those who are serious about getting one, there is a great Solo Skiff Owners Group on Facebook. Lots of good info on motor recommendations, rigging and general use. I had read early reviews stating that the 3.5 HP Tohatsu is adequate and the way to go, but this group has convinced me that for a lard butt like me a 5 or even a 6 is the way to go.

makobob · 02-15-2017, 07:47 PM

So who is going to be the FIRST to do a Greg Andrews roll in one of these at Leo? SDROB, that thing should outrun a GW so you would be good to go.

I found a Gregor 14 with almost new 20 Honda ready for Baja, Should be there in April. Thanks guys.

PapaDave · 02-16-2017, 06:01 AM

Quote:

Originally Posted by makobob

So who is going to be the FIRST to do a Greg Andrews roll in one of these at Leo? SDROB, that thing should outrun a GW so you would be good to go.

I found a Gregor 14 with almost new 20 Honda ready for Baja, Should be there in April. Thanks guys.

If you're going to use an outboard you might as well go with that...

makobob · 02-16-2017, 07:30 AM

Quote:

Originally Posted by PapaDave

If you're going to use an outboard you might as well go with that...

I went that way because of reliability, 20 hp 4 strokes just work and sip fuel. The smaller outboards seem to have more maintence and running problems including idle and fouled carbs. Only my opinion. TightLines.

Baja_Traveler · 02-16-2017, 08:44 AM

Quote:

Originally Posted by makobob

I went that way because of reliability, 20 hp 4 strokes just work and sip fuel. The smaller outboards seem to have more maintence and running problems including idle and fouled carbs. Only my opinion. TightLines.

Yep - in all my research on these little outboards - you'd better shut the valve and run the carb bowl dry after the end of the day, or suffer the consequences. Most likely because of the tiny jets on the carbs of these small engines are so easy to varnish up. Also recommended to add a marine fuel stabilizer.
Take care to do that, and they are extremely reliable and fuel efficient.

Also - I'm not about to be dragging an outboard out of the truck routinely that weighs over a hundred pounds. My goal is to go trailerless, simply because trailers are not allowed in the Sentri lane.

makobob · 02-16-2017, 10:13 AM

Quote:

Originally Posted by Baja_Traveler

Yep - in all my research on these little outboards - you'd better shut the valve and run the carb bowl dry after the end of the day, or suffer the consequences. Most likely because of the tiny jets on the carbs of these small engines are so easy to varnish up. Also recommended to add a marine fuel stabilizer.
Take care to do that, and they are extremely reliable and fuel efficient.

Also - I'm not about to be dragging an outboard out of the truck routinely that weighs over a hundred pounds. My goal is to go trailerless, simply because trailers are not allowed in the Sentri lane.

So Kai, are you going to leave the small outboard attatched to the yak transom or REMOVE it for transport, I do like the idea. Really increases the exploration range. All the bigger Roosters WERE caught at the island.

Question to OEX.............Transducer Mounting options?????????

Tight Lines.

Baja_Traveler · 02-16-2017, 11:29 AM

That all depends - if I go the route where I load it in the bed of the truck with a hitch extender, I'll leave it in place. If I decide to go up on the racks with one of those pivot loaders, the outboard will go in the bed of the truck. I'm still debating back and forth on it, but tending towards up on the rack.
I just feel its safer for the boat, not hanging out there for someone to run into, and you know how when you pass through the Sentri booth you have to go through those super tight turns that prevent gate crashing? Reducing overall truck length is an advantage - heck, I feel like I can barely make those turns as it is.

The transducer question has also crossed my mind. I thought it would be awesome for them to include a "Lowrance Ready" option like Hobie has. But that would involve them building a new roto mold - not an inexpensive undertaking. I see that people have mounted fishfinders with the cabling passing through a watertight fitting in the forward bulkhead, but I don't see detail on the actual transducer mount. Since these boats are first rotomolded just like our kayaks, and then given a second pass with a foaming compound (creating an 1 1/2" hull) I'm not sure how well a transducer would "shoot through" that thick of material. Further research will be needed.
The cool thing is - all the expensive accessories I bought for the PA14 can simply be swapped over to the Solo, all I would have to duplicate are the transducer and rod holder mounts.

Baja_Traveler · 02-16-2017, 07:25 PM

Here's the problem with researching the crap out of something - it costs me money. This is the first accessory I have to order, and it will be the bomb for the PA14 also for getting over sand and cobble, way nicer than the Hobie cart and it folds up into a super compact package for transporting (But costs twice as much also

).

Dynamic Dolly

makobob · 02-16-2017, 08:13 PM

Quote:

Originally Posted by Baja_Traveler

Here's the problem with researching the crap out of something - it costs me money. This is the first accessory I have to order, and it will be the bomb for the PA14 also for getting over sand and cobble, way nicer than the Hobie cart and it folds up into a super compact package for transporting (But costs twice as much also

).

Dynamic Dolly

BT, contact EOD he has a PA 14 on this cart. Get his oppinion he used it at my place.

GoGoGoJack · 02-18-2017, 08:03 PM

Quote:

Originally Posted by FullFlavorPike

I would get a kaboat before that. Similar capabilities and capacity, but you can roll up a kaboat.

Any reason this thing would be superior?

Perhaps a bit less munch-able than a Kaboat

Sent from my iPhone using Tapatalk

makobob · 02-19-2017, 12:26 PM

GREAT idea, two things do seem to stick out in my limited mind. First being a skiff it has to be registered in California and second, I doubt they will be allowed to fish most kayak tourneys with the motors attatched. A big plus point should be that they ARE NOT sit on tops so lake use should be assured. As for BAJA use they would be AWESOME.

Baja_Traveler · 02-19-2017, 12:52 PM

Definitely need registration - thats a requirement for every state being outboard powered, but where I couldn't bring myself to putting CF numbers on my PA, this would be no problem.

No kayak tournaments for this boat obviously, but thats what the PA is for. The Hobie is not going anywhere, this is just supplementing it.

Went down to OEX today to look at the boat going to the shows, and brought tape measure and paper. Took a bunch of measurements for planning purposes, Got it figured out how it will be stored in tandem with the PA. Figured out that if I loaded it in the bed of the truck, it would stick out only 4 1/2 feet past the tailgate. Most likely how I will be transporting it locally.
Figured out how to load the thing, both in the bed of the truck, and on the roof racks without having to do any heavy lifting, thus saving my back, as I'm not getting any younger. (this one I'll be building and proving out using the PA as a test case, and use it for that also).
Looking forward to fishing off it for sure. Figured out that with a 3 gallon tank I could fish from Bob's place all the way to Gonzaga Bay and back no problem.

02-15-2017, 05:24 PM	#25
Baja_Traveler Senior Member Join Date: Nov 2005 Location: Table 17, Bay Park Fish Co. Posts: 943	Exactly - this!! When I get mine I want Bob to get busy with his drone! For all those who are serious about getting one, there is a great Solo Skiff Owners Group on Facebook. Lots of good info on motor recommendations, rigging and general use. I had read early reviews stating that the 3.5 HP Tohatsu is adequate and the way to go, but this group has convinced me that for a lard butt like me a 5 or even a 6 is the way to go. Last edited by Baja_Traveler; 02-15-2017 at 05:33 PM.

02-15-2017, 07:47 PM	#26
makobob Baitless on Baja Join Date: May 2013 Location: Vista California, Gonzaga, San Quintin, Asuncion, Mag Bay Posts: 4,250	So who is going to be the FIRST to do a Greg Andrews roll in one of these at Leo? SDROB, that thing should outrun a GW so you would be good to go. I found a Gregor 14 with almost new 20 Honda ready for Baja, Should be there in April. Thanks guys. __________________ http://www.mako-ville.com Home 760-630-4470 Cell 760-520-2514 YES YOU CAN

02-16-2017, 07:25 PM	#32
Baja_Traveler Senior Member Join Date: Nov 2005 Location: Table 17, Bay Park Fish Co. Posts: 943	Here's the problem with researching the crap out of something - it costs me money. This is the first accessory I have to order, and it will be the bomb for the PA14 also for getting over sand and cobble, way nicer than the Hobie cart and it folds up into a super compact package for transporting (But costs twice as much also). Dynamic Dolly

02-19-2017, 12:26 PM	#35
makobob Baitless on Baja Join Date: May 2013 Location: Vista California, Gonzaga, San Quintin, Asuncion, Mag Bay Posts: 4,250	GREAT idea, two things do seem to stick out in my limited mind. First being a skiff it has to be registered in California and second, I doubt they will be allowed to fish most kayak tourneys with the motors attatched. A big plus point should be that they ARE NOT sit on tops so lake use should be assured. As for BAJA use they would be AWESOME. __________________ http://www.mako-ville.com Home 760-630-4470 Cell 760-520-2514 YES YOU CAN

02-15-2017, 08:37 AM	#21
YakHanded Thread Killer - sorry Join Date: Apr 2013 Location: San Clemente Posts: 256	Super cool! Here are some more videos stability test: https://www.youtube.com/watch?v=YYcBSvsgg4U Through minor lj-esque 'surf': https://www.youtube.com/watch?v=YD9x5WGUpo4 This is another company Hayaari Marine that makes a similar boat - pretty cool too: https://www.youtube.com/watch?v=BbMSfUmoW2Y https://www.youtube.com/watch?v=iA5mhRhnvIQ https://www.youtube.com/watch?v=0-pEGUtvdw0

02-15-2017, 09:10 AM	#22
farreola Senior Member Join Date: Nov 2015 Location: Calexico Posts: 134	There are tons of videos on YouTube. There are is one where it is going through white caps, another through surf and a nice DYI dolly.

02-15-2017, 09:24 AM	#23
sandico Member Join Date: Sep 2015 Location: San Diego Posts: 94	Yes we are going to be rigging up the Solo Skiff we have and bringing it to the shows. This is a unique kayak and has limitless rigging options. Unfortunately we will not be able to do any demo's until after the shows. Currently we are taking orders and they will be available in both OEX locations and come in 3 colors. Check it out here as well! http://www.kayakfishingsupplies.com/...-skiff/id/288/ Kerry OEX Mission Bay

02-16-2017, 11:29 AM	#31
Baja_Traveler Senior Member Join Date: Nov 2005 Location: Table 17, Bay Park Fish Co. Posts: 943	That all depends - if I go the route where I load it in the bed of the truck with a hitch extender, I'll leave it in place. If I decide to go up on the racks with one of those pivot loaders, the outboard will go in the bed of the truck. I'm still debating back and forth on it, but tending towards up on the rack. I just feel its safer for the boat, not hanging out there for someone to run into, and you know how when you pass through the Sentri booth you have to go through those super tight turns that prevent gate crashing? Reducing overall truck length is an advantage - heck, I feel like I can barely make those turns as it is. The transducer question has also crossed my mind. I thought it would be awesome for them to include a "Lowrance Ready" option like Hobie has. But that would involve them building a new roto mold - not an inexpensive undertaking. I see that people have mounted fishfinders with the cabling passing through a watertight fitting in the forward bulkhead, but I don't see detail on the actual transducer mount. Since these boats are first rotomolded just like our kayaks, and then given a second pass with a foaming compound (creating an 1 1/2" hull) I'm not sure how well a transducer would "shoot through" that thick of material. Further research will be needed. The cool thing is - all the expensive accessories I bought for the PA14 can simply be swapped over to the Solo, all I would have to duplicate are the transducer and rod holder mounts.

02-19-2017, 12:52 PM	#36
Baja_Traveler Senior Member Join Date: Nov 2005 Location: Table 17, Bay Park Fish Co. Posts: 943	Definitely need registration - thats a requirement for every state being outboard powered, but where I couldn't bring myself to putting CF numbers on my PA, this would be no problem. No kayak tournaments for this boat obviously, but thats what the PA is for. The Hobie is not going anywhere, this is just supplementing it. Went down to OEX today to look at the boat going to the shows, and brought tape measure and paper. Took a bunch of measurements for planning purposes, Got it figured out how it will be stored in tandem with the PA. Figured out that if I loaded it in the bed of the truck, it would stick out only 4 1/2 feet past the tailgate. Most likely how I will be transporting it locally. Figured out how to load the thing, both in the bed of the truck, and on the roof racks without having to do any heavy lifting, thus saving my back, as I'm not getting any younger. (this one I'll be building and proving out using the PA as a test case, and use it for that also). Looking forward to fishing off it for sure. Figured out that with a 3 gallon tank I could fish from Bob's place all the way to Gonzaga Bay and back no problem.