My first bait tank build - Kayak Fishing Adventures on Big Water’s Edge

William Novotny · 02-25-2012, 03:29 PM

Finally got the green monster totally fishable with the completion of my bait tank. Thank you Andy at OEX Sunset beach for your time and insight.

Decided to make a huge leap and go straight for the through hull system and here is how she turned out.

Standard 3.6gallon petfood container

90° angled pvc elbow

Another shot of the inside. Nozzle angled down at a 45° to slow down the current a bit.

Here is the 500gpr tsunami pump installed. I used marine goop on all seals then reinforce the pump with jb weld For added strength.

Heres the hose running back to the tankwell.

Another fitting in the tankwell leading to the intake on the tank

Should work well. Ill try it on tuesday. Havent put anything into electrical yet. Ill have a deck mounted rocker switch installed soon.

YakMedic · 02-25-2012, 04:53 PM

Looks like a lot of goop inside the hull. Did you rig a bilge pump too?

William Novotny · 02-25-2012, 05:00 PM

Just gooped alot of jb weld around the airator pump to be safe. It was hard to get inside to do a really clean job.

dorado50 · 02-25-2012, 05:07 PM

Excellent job... hoping pump is located where you can get to it on the water as impeller will cease with weed at some point and you will need to clear by removing "engine" from houseing! JB weld means the houseing can never be removed without damage to unit!

Iceman · 02-25-2012, 05:33 PM

he can still pop the top and clear the impeller, and replace the motor cartridge if ever needed. JB weld just around bottom. I prefer 5200 as it flexes. jb weld is almost like bondo. Still you should be good to go as long as you tightened down the strainer.

dorado50 · 02-25-2012, 06:41 PM

Yea, its evident impeller unit can be removed when not in the water, but is there access to remove in the water when needed!!!!! If you can't clear impeller when jammed while on the water the bait tank becomes a non factor...

echo1er · 02-25-2012, 07:01 PM

looks slick

William Novotny · 02-25-2012, 09:22 PM

This is my first build so I dont speak from experience but I did my homework and I feel that this will work well. The houseing is in an area that is accessible for maintnance. time on the water wil be the test but for now I'm confident with the design do to the number of people I see using it. The jb weld was to put my mind at ease in case it gets bumped on the water.

seriola_killer · 02-25-2012, 09:53 PM

Stupid question but I don't know...

Is this an aerator or bilge pump? And which one is proper for kayak bait tanks?
One more...

For a smaller tank wouldn't something like 60-90 gph be plenty?

William Novotny · 02-25-2012, 10:21 PM

Quote:

Originally Posted by seriola_kiler

Stupid question but I don't know...

Is this an aerator or bilge pump? And which one is proper for kayak bait tanks?
One more...

For a smaller tank wouldn't something like 60-90 gph be plenty?

1st question. The one im using is an aerator. Its good for thru hull systems. submersible bilge pumps are used for over the side tanks.

2nd. The pump is not on 100% of the time so its not actually moving that much water. You turn it on for 10 minutes every 15 minutes or so or put it on a timer

02-25-2012, 03:29 PM	#1
William Novotny The carpetbagger Join Date: Sep 2011 Location: tha newps Posts: 1,474	My first bait tank build Finally got the green monster totally fishable with the completion of my bait tank. Thank you Andy at OEX Sunset beach for your time and insight. Decided to make a huge leap and go straight for the through hull system and here is how she turned out. Standard 3.6gallon petfood container 90° angled pvc elbow Another shot of the inside. Nozzle angled down at a 45° to slow down the current a bit. Here is the 500gpr tsunami pump installed. I used marine goop on all seals then reinforce the pump with jb weld For added strength. Heres the hose running back to the tankwell. Another fitting in the tankwell leading to the intake on the tank Should work well. Ill try it on tuesday. Havent put anything into electrical yet. Ill have a deck mounted rocker switch installed soon. __________________ "The charm of fishing is that it is the pursuit of what is elusive but attainable, a perpetual series of occasions for hope." http://www.badinfluencetattoo.com/gallery.php?artist=21

02-25-2012, 05:00 PM	#3
William Novotny The carpetbagger Join Date: Sep 2011 Location: tha newps Posts: 1,474	Just gooped alot of jb weld around the airator pump to be safe. It was hard to get inside to do a really clean job. __________________ "The charm of fishing is that it is the pursuit of what is elusive but attainable, a perpetual series of occasions for hope." http://www.badinfluencetattoo.com/gallery.php?artist=21

02-25-2012, 05:33 PM	#5
Iceman Administrator Join Date: Mar 2005 Location: 1-2 miles off the point Posts: 6,948	he can still pop the top and clear the impeller, and replace the motor cartridge if ever needed. JB weld just around bottom. I prefer 5200 as it flexes. jb weld is almost like bondo. Still you should be good to go as long as you tightened down the strainer. __________________

02-25-2012, 09:22 PM	#8
William Novotny The carpetbagger Join Date: Sep 2011 Location: tha newps Posts: 1,474	This is my first build so I dont speak from experience but I did my homework and I feel that this will work well. The houseing is in an area that is accessible for maintnance. time on the water wil be the test but for now I'm confident with the design do to the number of people I see using it. The jb weld was to put my mind at ease in case it gets bumped on the water. __________________ "The charm of fishing is that it is the pursuit of what is elusive but attainable, a perpetual series of occasions for hope." http://www.badinfluencetattoo.com/gallery.php?artist=21

02-25-2012, 09:53 PM	#9
seriola_killer Sled Peddler Join Date: Feb 2012 Location: Bonita, Ca. Posts: 236	Stupid question but I don't know... Is this an aerator or bilge pump? And which one is proper for kayak bait tanks? One more... For a smaller tank wouldn't something like 60-90 gph be plenty? __________________ Jerry Moore Need a car or truck to yaul your yak? Ring me up. (619)988-3325

02-25-2012, 04:53 PM	#2
YakMedic Senior Member Join Date: Feb 2011 Location: Wrightwood Posts: 623	Looks like a lot of goop inside the hull. Did you rig a bilge pump too?

02-25-2012, 05:07 PM	#4
dorado50 Senior Member Join Date: Mar 2006 Location: La Jolla Shores Posts: 1,626	Excellent job... hoping pump is located where you can get to it on the water as impeller will cease with weed at some point and you will need to clear by removing "engine" from houseing! JB weld means the houseing can never be removed without damage to unit!

02-25-2012, 06:41 PM	#6
dorado50 Senior Member Join Date: Mar 2006 Location: La Jolla Shores Posts: 1,626	Yea, its evident impeller unit can be removed when not in the water, but is there access to remove in the water when needed!!!!! If you can't clear impeller when jammed while on the water the bait tank becomes a non factor...

02-25-2012, 07:01 PM	#7
echo1er Senior Member Join Date: Sep 2011 Posts: 598	looks slick