Revo--Transducer Location? - Kayak Fishing Adventures on Big Water’s Edge

Kailolo · 03-15-2011, 08:39 AM

For a Hobie Revo:
A common mounting spot seems is between the sail mast holder and the pedals. But this seems too close to the pedals, such that the pedals wouls enter the sonar cone or the DI sonar signal? Directly under the center hatch would interfere with good storage and face turbulence from the pedals. Comments?

GregAndrew · 03-15-2011, 09:00 AM

Not sure what the distance between the spot you mention and the fins is, but even the wide cone is no more than a little over 1 to 1. So say your fins stick down 16 inches, you would need your Xducer to be that far away to avoid seeing them. The typical narrow beam (200khz) cone angle is between 12 and 20 degrees, and the wide beam (50 or 83khz) is 45 and 60 degrees. At 60 degrees I believe the ratio is about 1.1 to 1 (you see 1.1 feet over for every 1 foot down).

dorado50 · 03-15-2011, 09:14 AM

Just locate it under the seat. Easy access and out of the way!

Regor · 03-15-2011, 09:24 AM

I have read posts elsewhere that have mounted and documented the results of transducer installs behind and forward of the pedals.

Results concluded - rear of the pedals near the seat produced a lot of interference.

Mine is forward near the mast and it works great. Also makes a nice place to bundle all the wires, and zip tie the battery when heading out.

GregAndrew · 03-15-2011, 09:28 AM

I misspoke. The ratio is about 1.1 to one, but you obviously only have to be 1/2 of that distance away because the other half is in the opposite direction.

Kaijuu · 03-15-2011, 03:25 PM

I have both the Outback and the Revo. Both my transducers are located between the mast and peddle system. I have no interference on either yak.

03-15-2011, 08:39 AM	#1
Kailolo Member Join Date: Aug 2010 Posts: 64	Revo--Transducer Location? For a Hobie Revo: A common mounting spot seems is between the sail mast holder and the pedals. But this seems too close to the pedals, such that the pedals wouls enter the sonar cone or the DI sonar signal? Directly under the center hatch would interfere with good storage and face turbulence from the pedals. Comments?

03-15-2011, 03:25 PM	#6
Kaijuu "Floater" Join Date: Sep 2010 Location: so cal Posts: 164	transducer location I have both the Outback and the Revo. Both my transducers are located between the mast and peddle system. I have no interference on either yak.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-15-2011, 09:00 AM	#2
GregAndrew Senior Member Join Date: Mar 2009 Posts: 2,384	Not sure what the distance between the spot you mention and the fins is, but even the wide cone is no more than a little over 1 to 1. So say your fins stick down 16 inches, you would need your Xducer to be that far away to avoid seeing them. The typical narrow beam (200khz) cone angle is between 12 and 20 degrees, and the wide beam (50 or 83khz) is 45 and 60 degrees. At 60 degrees I believe the ratio is about 1.1 to 1 (you see 1.1 feet over for every 1 foot down).

03-15-2011, 09:14 AM	#3
dorado50 Senior Member Join Date: Mar 2006 Location: La Jolla Shores Posts: 1,626	Just locate it under the seat. Easy access and out of the way!

03-15-2011, 09:24 AM	#4
Regor Greg Join Date: May 2010 Location: Chula Vista, ca Posts: 509	I have read posts elsewhere that have mounted and documented the results of transducer installs behind and forward of the pedals. Results concluded - rear of the pedals near the seat produced a lot of interference. Mine is forward near the mast and it works great. Also makes a nice place to bundle all the wires, and zip tie the battery when heading out.

03-15-2011, 09:28 AM	#5
GregAndrew Senior Member Join Date: Mar 2009 Posts: 2,384	I misspoke. The ratio is about 1.1 to one, but you obviously only have to be 1/2 of that distance away because the other half is in the opposite direction.