Hobie Revo/wheels question - Kayak Fishing Adventures on Big Water’s Edge

kansas · 09-06-2010, 09:23 AM

OK, so I finally got around to getting a set of wheels. A buddy was with me the first time I put them on. Getting the kayak off of the wheels was pretty easy. However, when I was done I became the entertainment of the day with people watching me try to lift the yak and install the wheels in the scupper holes. Has anyone perfected this fiasco?

dsafety · 09-06-2010, 09:30 AM

Just roll the kayak on its side, slide the support rods into the scupper holes and roll it back. Removing the unit is even easier. Lift the kayak by the stern until the thing falls off.

Bob

Ohana · 09-06-2010, 10:41 AM

Bob has it right for installing the wheels. Just make sure you do this before loading items on your kayak

As for taking them off, raising the stern so the wheels are off the ground normally works, but occasionally they do not fall out of the holes very easily. While it takes some stretching, while lifting the kayak by the stern, I use one leg to knock the wheels down and out of the holes. Not very elegant, but it works.

Kevin

tunaseeker · 09-06-2010, 11:29 AM

Just be careful with the scupper holes, I got a crack in mine and almost sank!

SeaEagle_1 · 09-06-2010, 12:23 PM

well i am lazy and usually have gear that is unsecured on my deck. so what i do is just wade out into the water just far enough (about 18" or 2ft) and just slide them under the boat, line up the rods with the holes and and then bring the wheels down and seat the wheels in the scubbers. sometimes it can take a bit of effort to get those wheels down, but it lets me wheel my yak right out of the water.

mrJB · 09-06-2010, 05:41 PM

You can also open the rear hatch and get an extra gripping or lifting hold...

09-06-2010, 09:23 AM	#1
kansas Junior Join Date: Jan 2009 Posts: 12	Hobie Revo/wheels question OK, so I finally got around to getting a set of wheels. A buddy was with me the first time I put them on. Getting the kayak off of the wheels was pretty easy. However, when I was done I became the entertainment of the day with people watching me try to lift the yak and install the wheels in the scupper holes. Has anyone perfected this fiasco?

09-06-2010, 05:41 PM	#6
mrJB Senior Member Join Date: Feb 2007 Location: O.C. Posts: 352	You can also open the rear hatch and get an extra gripping or lifting hold... __________________ "I Brake for Halibut"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-06-2010, 09:30 AM	#2
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Just roll the kayak on its side, slide the support rods into the scupper holes and roll it back. Removing the unit is even easier. Lift the kayak by the stern until the thing falls off. Bob

09-06-2010, 10:41 AM	#3
Ohana Senior Member Join Date: Oct 2009 Location: Coto de Caza, CA Posts: 155	Bob has it right for installing the wheels. Just make sure you do this before loading items on your kayak As for taking them off, raising the stern so the wheels are off the ground normally works, but occasionally they do not fall out of the holes very easily. While it takes some stretching, while lifting the kayak by the stern, I use one leg to knock the wheels down and out of the holes. Not very elegant, but it works. Kevin

09-06-2010, 11:29 AM	#4
tunaseeker TB Metal Art Join Date: Jul 2010 Location: San Diego Posts: 653	Just be careful with the scupper holes, I got a crack in mine and almost sank!

09-06-2010, 12:23 PM	#5
SeaEagle_1 Member Join Date: Feb 2009 Location: Santa Ana/But moving to Elsinore Posts: 32	well i am lazy and usually have gear that is unsecured on my deck. so what i do is just wade out into the water just far enough (about 18" or 2ft) and just slide them under the boat, line up the rods with the holes and and then bring the wheels down and seat the wheels in the scubbers. sometimes it can take a bit of effort to get those wheels down, but it lets me wheel my yak right out of the water.