Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 01-28-2020, 11:33 AM   #1
Nickrivers
Member
 
Join Date: Aug 2019
Location: Santa Paula
Posts: 32
Tie down methods for crates/coolers

Recently picked up a Engel 19qt Drybox/Cooler for my Outback. I was considering picking up their salt-rated tiedown kit they offer.

Never drilled any holes in my outback before. Any tips or things to look out for? should I forgo screws all together and go with clips like the HCrate?

Any input much appreciated!

Cheers

https://www.engelcoolers.com/tie-down-kit.html
Nickrivers is offline   Reply With Quote
Old 01-28-2020, 03:37 PM   #2
igotpron
Xcoastie
 
igotpron's Avatar
 
Join Date: Jun 2013
Location: Westminster
Posts: 285
Tie down methods for crates/coolers

I would avoid drilling holes into the well. Incase something unforeseeable happens and it ends up leaking. I would secure to the gunnels if possible. I’ve had good luck using the hobie bait tank straps and pad eyes. Use small screws 10-32 stainless with washers and nylock nuts on the inside.


Sent from my iPhone using Tapatalk
igotpron is offline   Reply With Quote
Old 01-30-2020, 04:24 AM   #3
TJones
Senior Member
 
TJones's Avatar
 
Join Date: Jan 2012
Posts: 2,526
Check into

The hobie bait tank straps. Figure a way to attach these straps to your crate and you will be golden. Some stainless steel screws and nuts should do the trick? You should be able to find this at your local marine supply. Give Andy a call to order kit. It comes with two straps that have quick release buckles. If you add 4 straps, one on each corner of your crate, it won’t be moving. Do a search for hobie bait tank straps and you can see kit. I used them on my vitals tank and it’s solid. Good luck.
TJones is offline   Reply With Quote
Old 01-30-2020, 04:28 AM   #4
TJones
Senior Member
 
TJones's Avatar
 
Join Date: Jan 2012
Posts: 2,526
My bad

Its 4 am. I didn’t realize someone suggested same exact thing. 😂
TJones is offline   Reply With Quote
Old 01-30-2020, 06:42 AM   #5
TJones
Senior Member
 
TJones's Avatar
 
Join Date: Jan 2012
Posts: 2,526
Hobie also has

extra large pad eyes that came out around 2017. this is useful if you are attaching multiple pieces of equipment to the same pad eye. With the suggested straps, mounting should be a breeze.
TJones is offline   Reply With Quote
Old 01-30-2020, 12:43 PM   #6
FISH11
Member
 
FISH11's Avatar
 
Join Date: Aug 2013
Location: Pine Valley when not fishing La Jolla
Posts: 2,643
anchoring Bait Tank or Crate

I installed several of these nylon eyelets on all my kayaks, place them in different areas for tying down everything including rod leashes or crates, etc. I install them on the top of the rail or inner side just below the top of the rail if you want to keep the top of the kayak side rail clear for loading onto car/truck racks. They can be installed using stainless screws, washers and nuts. If access to install the inside washers and nuts is a problem then use Aluminum pop rivets, these from OEX will spread out in three directions on the inside without needing access inside the hull or using washers. The pop rivets are considerably less expensive than stainless steel hardware. I am including links to these parts on OEX online order site. All you need is a 1/8" drill and a pop rivet hand gun, they install super fast and won't corrode. Also included is a picture from a Malibu X13 that I used to have with a self made bait tank and attached using 1/4" bungee cord with nylon snap in ends and made to the length needed. https://www.kayakfishingsupplies.com...ets-pack-of-10 https://www.kayakfishingsupplies.com...ets-pack-of-10
Attached Images
File Type: jpg 20170425_161545.jpg (55.1 KB, 48 views)
__________________
MARK ......... 2016 MALIBU X FACTOR, 2020 SOLO SKIFF (Fishing Kayak on Steroids )
FISH11 is offline   Reply With Quote
Old 01-30-2020, 02:58 PM   #7
Nickrivers
Member
 
Join Date: Aug 2019
Location: Santa Paula
Posts: 32
Awesome! Thanks for all the replies. While reading all the suggestions I did a search for some H-Rail Tie Downs and found these.

https://www.rammount.com/part/RAP-431U

Seems like a good option. As well as removable and versatile.

Might also keep me from drilling into my cooler although not a concern.
Nickrivers is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 05:16 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.