Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 09-21-2017, 10:18 AM   #1
DPevin
Member
 
DPevin's Avatar
 
Join Date: May 2016
Location: Dana Point
Posts: 96
Fish Finder Issue

Got my Garmin Striker 4 awhile ago and a used battery/charger (knowing full well I would need to get a new battery soon enough). Rigged everything up and first time out it worked great. Battery only has like 7 amps to it only ran for 6 hrs or so, but worked and I was happy.

Fast forward a couple months and it is all the sudden not working. Charged it for a whole afternoon and overnight. Plug it in and its not working. It will start up and flash the Garmin screen then power off. This is with the transducer cable plugged in. With it unplugged it powers up.

Is the batter just not holding enough of a charge? And when the transducer kicks in it draws to much and powers the unit off?

Just seeing if anyone has had a similar experience or not. I pretty confident the fix is to get a new battery/charger. It was just strange it worked perfectly fine then not.
DPevin is offline   Reply With Quote
Old 09-21-2017, 11:23 AM   #2
Dirty Curti
Senior Member
 
Dirty Curti's Avatar
 
Join Date: Jul 2012
Location: Oceanside, CA
Posts: 419
Sounds like my battery experience. Bought a new battery and all is good.
__________________


Dirty Curti is offline   Reply With Quote
Old 09-21-2017, 11:44 AM   #3
goldenglory18
Senior Member
 
goldenglory18's Avatar
 
Join Date: Feb 2015
Location: Seattle Area
Posts: 861
Might as well get a new battery, fully charge it, and try again.

If the same issue still happens, you might have an issue with the Transducer cable that is causing a short. Unit works without it, doesn't with it, leads me to think its something with that side of the system (corroded connector, pinched cable, etc.)
goldenglory18 is offline   Reply With Quote
Old 09-21-2017, 01:23 PM   #4
TJones
Senior Member
 
TJones's Avatar
 
Join Date: Jan 2012
Posts: 2,526
Or

Look for harbor freight coupon. Free volt ohm meter with any purchase. Really is nice for double checking that the battery took a charge so you don't have any surprises at launch site. Can also be used to check continuity which is helpful at diagnosing connection problems. Meter is relatively inexpensive and worth purchasing as to eliminate guess work.
TJones is offline   Reply With Quote
Old 09-21-2017, 02:33 PM   #5
DPevin
Member
 
DPevin's Avatar
 
Join Date: May 2016
Location: Dana Point
Posts: 96
Thanks all. Glad to hear it sounds similar to an issue someone else had.

New battery in my future.

I did think about the cable being an issue. But I literally only used it 1 time. And the cable looks perfect, as well as the connector. When I say it works without it, I mean it just starts up to the main menu. Usually with the transducer in it starts up to the sonar screen.

That is what leads me to believe that with the cable plugged in it is drawing too much juice (for what the battery has left in it, which is probably nothing) and just turning off.

We will see I guess.
DPevin is offline   Reply With Quote
Old 09-21-2017, 03:22 PM   #6
jruiz
Large Member
 
Join Date: Jul 2012
Location: La Verne, CA
Posts: 1,011
If you only have the battery plugged in and it lasts for hours on the highest brightness setting then I doubt it's the battery.
jruiz is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 04:27 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.