how to put 2 kayaks on roof - Kayak Fishing Adventures on Big Water’s Edge

tomahawk · 03-09-2014, 05:40 PM

I have a stealth 12 and stealth 14 I want to transport the roof of a C1500 with a shell. The shell has roof rails and I have 60 inch yakima bars with lowriders. The bars attach fine to the shell. The combined kayak width is slightly greater than bars. I the yaks on the roof yesterday and was playing around with pvc cradles. I was hoping someone else had done this so i wouldn't have re-invent something. i looked yakima's solutions and would interested in user comments on how they fit with the malibu hull (hull seems pretty flat compared to saddle angles).
thanks,
Tom

Dave k · 03-10-2014, 07:22 AM

Check out the Malone saddles.

It's basically a V that mounts in the middle, so you can have part of the yak hanging over the bars on the side is needed. I was able to haul 2 on a Mazda with crossbars that I believe we're something like 54".

Good luck.

chxh8me · 03-10-2014, 07:36 AM

You can go with a stacker too. Pretty much all the rack companies make them. I went with the Inno stacker (INA 450), based on price and what comes with it; Padded vertical bars and padded cradles.

I originally tried going with extra long cross bars and two sets of yakima saddles, but felt like the 65 inch bars would have taken someone's eye out due to how far they stuck out.

So now I have the stacker for when I need to transport 2, or one set of saddles for when it's just me going out.

CheapPelican · 03-10-2014, 07:50 AM

I have 48" bars and use J cradles. Might be a pain to lift them that high on to a full size truck.

Do this hack. Makes it much easier.

Quote:

Originally Posted by inbx3

So I was getting tired of having my cradles rotate everytime I hit with my kayak. The Yakima bars are round and no matter how much I tighten them the alwys end up like this.

So I figured there has to be a way to keep them straight so over to Home Depot I went and $8 later here's the finished solution.

I took a couple of 3/4" electrical conduit, cut it to the correct size, drilled a couple of holes in each end to line them up with the J cradles, flattened out the ends a bit and now they don't rotate.

03-09-2014, 05:40 PM	#1
tomahawk Senior Member Join Date: Aug 2012 Posts: 109	how to put 2 kayaks on roof I have a stealth 12 and stealth 14 I want to transport the roof of a C1500 with a shell. The shell has roof rails and I have 60 inch yakima bars with lowriders. The bars attach fine to the shell. The combined kayak width is slightly greater than bars. I the yaks on the roof yesterday and was playing around with pvc cradles. I was hoping someone else had done this so i wouldn't have re-invent something. i looked yakima's solutions and would interested in user comments on how they fit with the malibu hull (hull seems pretty flat compared to saddle angles). thanks, Tom

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-10-2014, 07:22 AM	#2
Dave k Senior Member Join Date: Apr 2011 Posts: 110	Check out the Malone saddles. It's basically a V that mounts in the middle, so you can have part of the yak hanging over the bars on the side is needed. I was able to haul 2 on a Mazda with crossbars that I believe we're something like 54". Good luck.

03-10-2014, 07:36 AM	#3
chxh8me Senior Member Join Date: Jul 2013 Location: Thousand Oaks Posts: 182	You can go with a stacker too. Pretty much all the rack companies make them. I went with the Inno stacker (INA 450), based on price and what comes with it; Padded vertical bars and padded cradles. I originally tried going with extra long cross bars and two sets of yakima saddles, but felt like the 65 inch bars would have taken someone's eye out due to how far they stuck out. So now I have the stacker for when I need to transport 2, or one set of saddles for when it's just me going out.