Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion
Home Forum Online Store Information LJ Webcam Gallery Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
Old 01-11-2011, 11:31 PM   #1
wiredantz
Currently @ MLO Territory
 
wiredantz's Avatar
 
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
What am I Missing Hummingbird 161?

Hello,


Hello one more, I am in the middle of installing my fish finder, and I am trying to figure out how to run my bait tank and FF at the same time.

I have one battery with one connection and i have two devices that need power. I have a bait tank on a timer switch that connects to the battery via the plug and i have a hummingbird 161 that will be connected to a inline fuse to a plug.

As it stands now, I need to disconnect one to power the other.

B.W.E How do i power both?


Thank You




wiredantz is offline   Reply With Quote
Old 01-12-2011, 01:00 AM   #2
jorluivil
Senior Member
 
jorluivil's Avatar
 
Join Date: Apr 2010
Posts: 6,856
Easy fix.....get a second battery. 12volt for your FF and a 6volt for your bait tank....thats the norm with most yakkers. I doubt a single battery will have enough juice to power two devices for more than 2 -3 hours.
jorluivil is offline   Reply With Quote
Old 01-12-2011, 06:54 AM   #3
wiseguy
Senior Member
 
wiseguy's Avatar
 
Join Date: Aug 2008
Location: Long Beach
Posts: 427
yup! you need two separate batteries. 6v for the bait tank and 12v for the FF.
wiseguy is offline   Reply With Quote
Old 01-12-2011, 08:20 AM   #4
tagyak
Senior Member
 
tagyak's Avatar
 
Join Date: Jun 2010
Location: Alhambra
Posts: 506
6v???

yes, two batteries, but since you have your bait tank on a timer switch, you can use a 12v battery. the 6v battery are recommended for those who don't have a timer on their setup.

also you can use a dry bag to store the other battery. they are cheaper than buying another dry box.
tagyak is offline   Reply With Quote
Old 01-12-2011, 09:12 AM   #5
mtnbykr2
Senior Member
 
mtnbykr2's Avatar
 
Join Date: Sep 2009
Location: newbury park ca
Posts: 2,323
I had an XFactor for my first boat, and I did run both the meter and the bait tank with one battery, it does work but only a few hours, same set up you are showing, better to run two batteries like everyone said...no fun when you are in em and then the meter dies
mtnbykr2 is offline   Reply With Quote
Old 01-12-2011, 09:27 AM   #6
INGRIDSDAD
Senior Member
 
Join Date: Oct 2007
Location: Riverside
Posts: 108
I ran this same setup on my x-factor a couple years ago and you will have a tough time with the bait tank flush mount battery connection. Make sure you use alot of dielctric gease because that area is always getting wet.

If i did it again i would have the battery hard wired and attached to the bait tank,(good use for the pelican box) and have another battery in a bag up front for the FF.

Looks like a sweet ride.
INGRIDSDAD is offline   Reply With Quote
Old 01-12-2011, 09:43 AM   #7
wiredantz
Currently @ MLO Territory
 
wiredantz's Avatar
 
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
Thanks for the replies.


I will go to radio shack and pick a battery connector for my second battery and pick up a dry bag.
wiredantz is offline   Reply With Quote
Old 01-12-2011, 10:11 AM   #8
Jimmyz123
Senior Member
 
Jimmyz123's Avatar
 
Join Date: Mar 2010
Location: San Diego
Posts: 2,385
2 Batteries seems to be the ticket. After being out on the water like I was yesterday I learned that you for sure need one to power the FF and one for the bait tank. Had I used one battery for both I would have lost both before the end of the day.
Jimmyz123 is offline   Reply With Quote
Old 01-13-2011, 01:00 PM   #9
wiredantz
Currently @ MLO Territory
 
wiredantz's Avatar
 
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
X-factor transducer location

Thanks for the replies, it took me 4 hours to finish setting up everything with 2 batteries. I tested everything out and everything turns on.

I ended putting the transducer under the a piece of foam that supports my x-factor seat. I figured since its the lowest part of the kayak, i would just put some water in there and it "should" read fine.


we will see...

I really had a hard time trying to find a good place to set the transducer on the x-factor.



Last edited by wiredantz; 01-13-2011 at 06:47 PM. Reason: new title
wiredantz is offline   Reply With Quote
Old 01-16-2011, 08:58 AM   #10
wiredantz
Currently @ MLO Territory
 
wiredantz's Avatar
 
Join Date: Dec 2010
Location: Under the Shadow
Posts: 2,290
I tested the transducer under the foam bad under the seat and with about 2 cups of water it worked GREAT!!!! just FYI
wiredantz is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 05:48 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.