storing stuff in the kayak - Kayak Fishing Adventures on Big Water’s Edge

old_rookie · 07-02-2010, 08:05 PM

So I want to put my stuff - tackle, pliers, knife, net.... in the kayak, but it is wide open down there. What is a good way to keep it from moving to the bow/stern so I can grab my stuff when opening the hatch or rod pod?

I was thinking of tying string to the stuff so I can pull it back out.

MarkT · 07-02-2010, 09:00 PM

You could put small stuff in a plastic box stuck to the bottom with velcro or in a bag and hang from hooks. You can stick some pool noodles down there to add boyancy and it can block stuff sliding around... of course that could prevent you from putting rods down below depending on what kind of yak you've got. .. what kind of yak do you have?

Amish Ed · 07-02-2010, 09:42 PM

I've used nylon stuff sacks and tied the draw strings to the hatch lid. It worked. Cutting down pool noodles to make bulkheads works too. They just need to be well mounted or they don't hold their place while surf launching.

bluesquids · 07-02-2010, 09:46 PM

I took a collapsable 5 gallon water container used for camping and cut it in half. This gives me two trays about 14"x 14''X 7" that are collapsable, they can be crammed into tight spaces and fit in any sized hatch. Walmart has them pretty cheap.

old_rookie · 07-02-2010, 09:51 PM

Quote:

Originally Posted by MarkT

.. what kind of yak do you have?

OK Trident 13

dsafety · 07-02-2010, 11:01 PM

I don't know the Trident but if you have a center hatch, you can probably put some sort of a tray in the accessible area. I have a Revo and the hatch the easily accessible area is accessed by a small round hatch. The storage area is fairly large but the hatch is too small to get any rigid thing into.

My solution was to take the lid of a large rectangular storage container, (about 18" x 30"). I cut the plastic in half so it could be bent and shoved into the hatch. While inside, I reassembled the lid and tied the halves together with some zip ties.

Once assembled inside, I had a relatively flat sheet of plastic that was raised above the bottom of the hull by an inch or so, (to stay relatively dry). To finish things off, I glued some pool noodles to the edges of this lid to keep stuff from sliding front to back and side to side.

My setup is not perfect but it creates a fairly large, dry area that keeps my tackle from sliding out of reach while keeping the stuff I put in this area out of standing water.

Bob

MarkT · 07-03-2010, 10:17 AM

Isn't there a small tray under the rod pod hatch that you can put pliers and what not in? I'd go with stuff sacks suspended to either side of the rod pod hatch. I wouldn't want to build bulkheads with pool noodles because you'd loose the benefits of the rod pod for underdeck rod storage.

rrdstarr · 07-03-2010, 03:25 PM

I plan to make a new rodpod cover that looks like the 2011 Angler trident.

robmandel · 07-04-2010, 10:47 PM

Quote:

Originally Posted by old_rookie

OK Trident 13

http://www.kayakfishingsupplies.com/...torage-/Detail

this fits in the rectangular section right behind the seat. works great on my T15. it's not inside, but it holds tons of stuff and seals great. alot easier to get things right behind you then to constantly open the hatch and dig. save the rod pod area for rods when you launch.

or, just goop some foam blocks or pieces of pool noodle to the bottom. they'll stop anything from sliding backwards.

another thing that is really good is to get a milk crate or one of those plastic file folder crates from staples, and use strap-loc some pvc tubes inside of it. you can put gaffs, bogas, pliers, etc., in the tubes, not to mention additional rods.

Ed · 07-05-2010, 07:53 AM

jorluivil · 07-08-2010, 01:10 AM

Quote:

Originally Posted by Ed

Are those clips held down by rivets? Did you use Goop or 5200 to seal the holes?

07-02-2010, 08:05 PM	#1
old_rookie Senior Member Join Date: Mar 2010 Location: Santee Posts: 904	storing stuff in the kayak So I want to put my stuff - tackle, pliers, knife, net.... in the kayak, but it is wide open down there. What is a good way to keep it from moving to the bow/stern so I can grab my stuff when opening the hatch or rod pod? I was thinking of tying string to the stuff so I can pull it back out.

07-02-2010, 09:42 PM	#3
Amish Ed Senior Member Join Date: Jun 2005 Location: Grants Pass, OR Posts: 1,906	I've used nylon stuff sacks and tied the draw strings to the hatch lid. It worked. Cutting down pool noodles to make bulkheads works too. They just need to be well mounted or they don't hold their place while surf launching. __________________ Amish Ed You can't catch it again if it's dead!

07-02-2010, 09:46 PM	#4
bluesquids Senior Member Join Date: Mar 2005 Location: Jamul, CA Posts: 243	I took a collapsable 5 gallon water container used for camping and cut it in half. This gives me two trays about 14"x 14''X 7" that are collapsable, they can be crammed into tight spaces and fit in any sized hatch. Walmart has them pretty cheap. __________________ Thanks, bluesquids

07-03-2010, 03:25 PM	#8
rrdstarr Junior Join Date: May 2010 Location: Victoria, BC Posts: 9	I plan to make a new rodpod cover that looks like the 2011 Angler trident. __________________ -Rick OK PT-13' sand coloured Pygmy Boats Borealis XL 17'

07-05-2010, 07:53 AM	#10
Ed Fringe Head Join Date: Mar 2005 Location: Drippin Chicken Water Ranch Posts: 140	__________________ "If cabbage was good for you, rabbits would be big as bears" (Adi)

07-02-2010, 09:00 PM	#2
MarkT Deep Release Specialist Join Date: Aug 2008 Location: Mission Viejo Posts: 94	You could put small stuff in a plastic box stuck to the bottom with velcro or in a bag and hang from hooks. You can stick some pool noodles down there to add boyancy and it can block stuff sliding around... of course that could prevent you from putting rods down below depending on what kind of yak you've got. .. what kind of yak do you have?

07-02-2010, 11:01 PM	#6
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	I don't know the Trident but if you have a center hatch, you can probably put some sort of a tray in the accessible area. I have a Revo and the hatch the easily accessible area is accessed by a small round hatch. The storage area is fairly large but the hatch is too small to get any rigid thing into. My solution was to take the lid of a large rectangular storage container, (about 18" x 30"). I cut the plastic in half so it could be bent and shoved into the hatch. While inside, I reassembled the lid and tied the halves together with some zip ties. Once assembled inside, I had a relatively flat sheet of plastic that was raised above the bottom of the hull by an inch or so, (to stay relatively dry). To finish things off, I glued some pool noodles to the edges of this lid to keep stuff from sliding front to back and side to side. My setup is not perfect but it creates a fairly large, dry area that keeps my tackle from sliding out of reach while keeping the stuff I put in this area out of standing water. Bob

07-03-2010, 10:17 AM	#7
MarkT Deep Release Specialist Join Date: Aug 2008 Location: Mission Viejo Posts: 94	Isn't there a small tray under the rod pod hatch that you can put pliers and what not in? I'd go with stuff sacks suspended to either side of the rod pod hatch. I wouldn't want to build bulkheads with pool noodles because you'd loose the benefits of the rod pod for underdeck rod storage.