My Latest Hobie Revo Mod - Kayak Fishing Adventures on Big Water’s Edge

dsafety · 07-03-2008, 06:42 PM

As I get to know my Hobie Revolution, I find much to praise but still a few shortcomings. Today I came up with a way to fix one of the problems that has bothered me since I first set this kayak in the water.

While there is plenty of storage space in the Revolution, the only space that is easily accessable while on the water is the area serviced by the center hatch cover. Unfortunately, this area is basically a big open tub. Due to the limiation of the hatch size, you can only reach so far into this opening. In addition, since there are no baffles to keep stuff from sliding from bow to stern, you never know where the things you try to store here will end up.

In addition, I have found that the seals on the hatch covers are not very good so after a surf launch, there is usually a little water in the bottom of the boat and anything that is just set on the plastic usually gets soaked with water.

The solution... create some storage trays that can only move within the center hatch space. Make these trays sit above any standing water and allow for drainage should any water get splashed into the trays.

The project was easy. It took about ten minutes and cost less than $6.

I have posted some photos below.

The first photo shows the the plastic trays I picked up at Target for a couple bucks each.

The second photo shows the optional drain holes drilled into the bottom of each tray.

Photo 3 shows holes drilled into the sides of the trays to allow for the zip ties to bind them together in the final step.

Photo 4 shows the trays being inserted into the kayak, one at a time. It is a tight fit but these trays bend easily and can be forced through the opening.

Photo 5 The trays are in the compartment and holes for the zip ties are aligned.

The last photo shows the trays with the zip ties attach. The tails were trimmed later.

I have not yet tried this system on the water but I believe that it will be the solution to my annoying storage problems.

I have a couple more interesting Revo mods to share with everyone. Stay tuned for the trolling bar with rod holders and the removable rod holder setup that installs in the Hobie cup holder.

Bob

BWE · 07-03-2008, 07:03 PM

Simple, cheap and easy.

Thanks for sharing!!!

sdcityboy · 07-03-2008, 07:15 PM

sounds cool Bob. i put pool noodles in thru that center hatch and put it in a U shape,one at front and one at rear, now nothing slides out of reach. now if you can find any purpose for the rear hatch please let me know.

dsafety · 07-03-2008, 07:33 PM

I tried the noodles before coming up with this idea. Noodles work but do not address the problem of keeping small items within reach. They also do not address the problem of keeping things relatively dry.

I think that this is a better solution. As for the stern hatch, I think that it is just a cosmetic feature. I use it as an access point when I wash out my kayak and need to wipe up the remaining water. These trays would work just as well there and they might provide a good place to store a battery or something like that.

Bob

savage · 07-03-2008, 07:44 PM

Thanks for the info.

THE DARKHORSE · 07-03-2008, 08:01 PM

I kinda like the possability of a can of beer dissapearing on May 18th

, to show up a month and a half later (when I really needed it)

. Thanks for sharing your ideas.

aclozer · 07-07-2008, 10:47 AM

I love this post. Sometimes we make it harder than it is. This looks simple and effective.

dsafety · 07-11-2008, 08:07 PM

I went fishing today with this tray in my kayak. In general, I think the thing worked quite well. Everything that I put in the tray was easily accessable and stayed dry. I put all my tackle in those resusable plastic containers from ZipLock. The trays hold about eight of these containers. The problem was that I usually had to take most the containers out to find what I was looking for because they all looked alike.

This is not a big deal but I suspect that there is a better way to organize things in these trays. Maybe I need to color code the containers or somehow label each one so they are easy to recognize.

Until next time.

Bob

Montesdad · 07-13-2008, 05:35 PM

I have two similar trays in my Revo loosely zip tied together to hold my misc. stuff (food, rope, fishing tackle trays, even holds my travel coffee mug - always nice to enjoy some hot coffee and a croissant while peddeling out to the fishing areas)

by having them loosely zip tied together, my center bucket fits just fine if I slide the trays off center a few inches. One can shave or cut the sides of the trays down a half inch or so if necessary for a better fit for the Hobie bucket.

Bob - nothing wrong with taking a magic marker and labeling the lids of your tupperware -

I have a larger Tupperware container in my front hatch to hold my battery, dry bag, fish finder etc. when not installed - not too hard to get in there and once it's in, keeps stuff from sliding around

bajadog · 07-14-2008, 05:20 AM

Montesdad is that a PVC fish finder mount?

Montesdad · 07-14-2008, 06:06 AM

Yes - PVC

$3.00 worth of parts and some spare schedule 40 1/2" PVC - the mounting plate is an old plastic cutting board I used to use for cutting up fish.

The pipe did go all the way to the bottom of the mast tube but it was way too long so now it only goes in about 3-4". The unit was a little long for storing easily for going and coming in the surf - now, works just fine.

I put an o-ring on the post up near the top where it touches the top of the mast tube so it helps keep it from moving - the post is snugged up with some black electricians tape at the top and the bottom of the post so it's fairly tight but goes in and comes out easily. Borrowed the design from all the others I've seen.

made the bungee -

07-03-2008, 07:15 PM	#3
sdcityboy Senior Member Join Date: Aug 2007 Location: south park (san diego),CA Posts: 119	sounds cool Bob. i put pool noodles in thru that center hatch and put it in a U shape,one at front and one at rear, now nothing slides out of reach. now if you can find any purpose for the rear hatch please let me know. __________________ he hates these cans!

07-03-2008, 07:33 PM	#4
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Noodles I tried the noodles before coming up with this idea. Noodles work but do not address the problem of keeping small items within reach. They also do not address the problem of keeping things relatively dry. I think that this is a better solution. As for the stern hatch, I think that it is just a cosmetic feature. I use it as an access point when I wash out my kayak and need to wipe up the remaining water. These trays would work just as well there and they might provide a good place to store a battery or something like that. Bob

07-03-2008, 08:01 PM	#6
THE DARKHORSE Senior Member Join Date: Mar 2007 Location: Seven minutes from the launch! Posts: 987	Yeah but............. I kinda like the possability of a can of beer dissapearing on May 18th , to show up a month and a half later (when I really needed it) . Thanks for sharing your ideas. __________________

07-07-2008, 10:47 AM	#7
aclozer Member Join Date: Oct 2006 Location: Carlsbad Posts: 48	Outstanding I love this post. Sometimes we make it harder than it is. This looks simple and effective.

07-11-2008, 08:07 PM	#8
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Followup Report I went fishing today with this tray in my kayak. In general, I think the thing worked quite well. Everything that I put in the tray was easily accessable and stayed dry. I put all my tackle in those resusable plastic containers from ZipLock. The trays hold about eight of these containers. The problem was that I usually had to take most the containers out to find what I was looking for because they all looked alike. This is not a big deal but I suspect that there is a better way to organize things in these trays. Maybe I need to color code the containers or somehow label each one so they are easy to recognize. Until next time. Bob

07-03-2008, 07:03 PM	#2
BWE Administrator Join Date: Feb 2007 Posts: 131	Simple, cheap and easy. Thanks for sharing!!!

07-03-2008, 07:44 PM	#5
savage Junior Member Join Date: Jun 2007 Location: fallbrook ca. Posts: 8	Thanks for the info.

07-13-2008, 05:35 PM	#9
Montesdad Grey Haired Senior Member Join Date: Apr 2008 Location: So. Orange County Posts: 53	I have two similar trays in my Revo loosely zip tied together to hold my misc. stuff (food, rope, fishing tackle trays, even holds my travel coffee mug - always nice to enjoy some hot coffee and a croissant while peddeling out to the fishing areas) by having them loosely zip tied together, my center bucket fits just fine if I slide the trays off center a few inches. One can shave or cut the sides of the trays down a half inch or so if necessary for a better fit for the Hobie bucket. Bob - nothing wrong with taking a magic marker and labeling the lids of your tupperware - I have a larger Tupperware container in my front hatch to hold my battery, dry bag, fish finder etc. when not installed - not too hard to get in there and once it's in, keeps stuff from sliding around Last edited by Montesdad; 07-13-2008 at 09:14 PM.

07-14-2008, 05:20 AM	#10
bajadog I eats what I kills Join Date: Apr 2008 Location: San Diego Posts: 393	Montesdad is that a PVC fish finder mount? __________________ Please release bill-fish.

07-14-2008, 06:06 AM	#11
Montesdad Grey Haired Senior Member Join Date: Apr 2008 Location: So. Orange County Posts: 53	Yes - PVC $3.00 worth of parts and some spare schedule 40 1/2" PVC - the mounting plate is an old plastic cutting board I used to use for cutting up fish. The pipe did go all the way to the bottom of the mast tube but it was way too long so now it only goes in about 3-4". The unit was a little long for storing easily for going and coming in the surf - now, works just fine. I put an o-ring on the post up near the top where it touches the top of the mast tube so it helps keep it from moving - the post is snugged up with some black electricians tape at the top and the bottom of the post so it's fairly tight but goes in and comes out easily. Borrowed the design from all the others I've seen. made the bungee -