Storing rods inside Kayak hull during launch

[SoCalEDC]

Anyone successfully do this in an outback, and still able to retrieve the rods when on the water? It was no big deal in my last yak cause of the rod pod, but on Saturday I put the rods in the hull on my outback (through the front hatch) in preparation for Sundays launch (which didn't pan out unfortunately), but I was concerned I wouldn't be able to get them out once I was out on the water. I have only surf launched a couple of times, so I'm not 100% comfortable with leaving my rods out as I don't want to break them if the kayak is tossed over and they're stuck in a rod holder.

Thanks in advance guys.

[matthew7!]

My buddy uses a out back he leaches all his rods and leaves them in the rod holder. Any extra rods he lays flat and bungees them down.


Sent from my iPhone using Tapatalk

[BenCantrell]

Originally Posted by matthew7!

Any extra rods he lays flat and bungees them down.

That's what I was going to suggest. Bungee them as flat as possible against the deck of the kayak so nothing would snap if you roll.

[Revoguys]

Yea Ive seen guys put their reels in a watertight bag and stuff it in the hull and put their reels on while they’re out there, also do what other guys are saying tie all their rods together and lay them flat and tie them down to the yak in case you flip. Truthfully if you go out on days that the surf is low you should be good. Just cut all your lures, jigs and hooks off your line before landing just in case you do flip you don’t hook yourself. Tight lines 🤙🏾

[f'nsabiki]

I've had an Outback for many years. I wrap the rods together, and put the reels in a heavy duty trash bag. For the rods, I slice a pool noodle in half and place it around the rods and lash them to the kayak. http://www.bigwatersedge.com/bwevb/a...1&d=1583911704
http://www.bigwatersedge.com/bwevb/a...1&d=1583911704
http://www.bigwatersedge.com/bwevb/a...1&d=1583912457

[SoCalEDC]

Thanks for all of the replies guys. Also just realised I posted this on the wrong subforum, apologies.

[monstahfish]

If you do slide your rods in, make sure you do it butt end first. That way when you slide the out on the water, you end up with the sturdy end in your hand. I have a new outback and use the h-tracks to launch with my fly rods pinned horizontal by the bungee. In most cases I just launch with my rods in the vertical holders of my livewell or crate and safety bungees on them.

[SoCalEDC]

Originally Posted by monstahfish

If you do slide your rods in, make sure you do it butt end first. That way when you slide the out on the water, you end up with the sturdy end in your hand. I have a new outback and use the h-tracks to launch with my fly rods pinned horizontal by the bungee. In most cases I just launch with my rods in the vertical holders of my livewell or crate and safety bungees on them.

Thanks for the heads up. Due to the geometry of the hatches, the hull, the drive well, and the thickness/stiffness of my rods the would only go tip first trough the front hatch and on the outside of the drive well. I don't think I can get them out of the front hatch despite the vertical orientation. I was planning to shimmy down the yak to the bow and retrieve them reverse of how they went in. With that said, I think I am going to try and store them the way you described with the bungee/H-rail method.

I don't particularly like to have to put the reels on on the water but I may have to work with it that way until I am comfortable with the rods vertical during launch.

[TJones]

Originally Posted by monstahfish

If you do slide your rods in, make sure you do it butt end first. That way when you slide the out on the water, you end up with the sturdy end in your hand. I have a new outback and use the h-tracks to launch with my fly rods pinned horizontal by the bungee. In most cases I just launch with my rods in the vertical holders of my livewell or crate and safety bungees on them.

2018 or lower years. I've done it many times with the reels attached. I also probably removed foam from inside to make it happen. I have always done tip first though, and when I would get to butt end of rod you have to really manipulate it or bend it slightly. all lures and lines should be wound up to reduce problems, and yes I have gotten the tips stuck a few times. I saw a post for measurements for new models and the hatch is narrower in width, but height remains the same. that leads me to believe that it could be done on the newer models? one thing to mention is that with the squeeze being so tight, don't be surprised if your rubber hatch seal comes unglued. hope this helps. my personally technique is to store rods and reels in a dry location like the hull when launching and landing. the ability to store rods should be a standard option when designing these things. JMO.

[filippo]

Originally Posted by Revoguys

Just cut all your lures, jigs and hooks off your line before landing just in case you do flip you don’t hook yourself. Tight lines 🤙🏾

Couldn't agree more!! Happened to me once. Flew off my kayak at landing, kayak landed on me, I got hooked, my rod was fully bento, weight of the yak on the rod & line and felt my skin would get ripped off, had to have my buddy and someone else help me get the line cut since waves were splashing against me and my kayak. One word: PAINFUL! Lesson learned. Oh, I emailed Rapala saying I didn't get to use their lure to catch a real fish, and they mailed me a brand new lure free -- that was nice!

[ProfessorLongArms]

This is one I've been noodling on for a while, and very recently had a nice big reminder on.

On big surf days where I launch, there's always a non-zero chance of going over... Especially in an outback. We *never* launch with rods up. I also stow my reels in my square hatch.

I always take my reels off my rods since worse than breaking a rod is getting that super fine sand in your reel if you bail in the surf zone.

What do I do? I keep a bunch of those Nite Ize rubber twist ties handy, and lash all of my rods together. I pass the buts of my reels under the strap that holds my bait tank in place. Then I tie off at the handle mid-kayak. Then for extra measure, I have a velcro strap at the front of my kayak bolted on that the rod tips pass through.

On my Revo, I decided I didn't actually need that extra bit at the front, but it's a good extra measure.

Bungees? I don't trust 'em after losing a rod from the oar holder on a launch once. Assume the force from the launch will *really* pull on anything not thoroughly secured.

This is a timely post of course, as I just snapped my sabiki rod and a (thankfully)cheap turner's californian rod in half because everyone else had their rods up, it was a small surf day, and I got distracted and just plain effed up on a launch. My torium and my lexa are now in the capable hands of their respective manufacturers as they work to remove every last grain of sand they can at 40-50 bucks a pop.

Had I actually followed my own rule, I would have just been a bit soggy and sandy, and given it another pass.

I am very much tempted to try a rod pod one of these days. Thinking I might sell my scupper and get an older trident for just that on dive days.

[BenCantrell]

I have a confession to make. Lately I've been doing all my landings backwards, and I've become so comfortable doing it that way that I've been leaving my rods in the rod holders.

[SoCalEDC]

Originally Posted by ProfessorLongArms

This is one I've been noodling on for a while, and very recently had a nice big reminder on.

On big surf days where I launch, there's always a non-zero chance of going over... Especially in an outback. We *never* launch with rods up. I also stow my reels in my square hatch.

I always take my reels off my rods since worse than breaking a rod is getting that super fine sand in your reel if you bail in the surf zone.

What do I do? I keep a bunch of those Nite Ize rubber twist ties handy, and lash all of my rods together. I pass the buts of my reels under the strap that holds my bait tank in place. Then I tie off at the handle mid-kayak. Then for extra measure, I have a velcro strap at the front of my kayak bolted on that the rod tips pass through.

On my Revo, I decided I didn't actually need that extra bit at the front, but it's a good extra measure.

Bungees? I don't trust 'em after losing a rod from the oar holder on a launch once. Assume the force from the launch will *really* pull on anything not thoroughly secured.

This is a timely post of course, as I just snapped my sabiki rod and a (thankfully)cheap turner's californian rod in half because everyone else had their rods up, it was a small surf day, and I got distracted and just plain effed up on a launch. My torium and my lexa are now in the capable hands of their respective manufacturers as they work to remove every last grain of sand they can at 40-50 bucks a pop.

Had I actually followed my own rule, I would have just been a bit soggy and sandy, and given it another pass.

I am very much tempted to try a rod pod one of these days. Thinking I might sell my scupper and get an older trident for just that on dive days.

This is fantastic info and very thorough explanation of how you tie them down, i appreciate it.

As far as the trident goes, as a previous trident owner, i can confirm that i would fit (2) spinning rods (7'-8' rods, bg4000, bg5000 sized reels) and (2) casting rods (a daiwa sealine 50H, and an avet sx5.3) in the hull with reels attached, and be able to retrieve them with ease out on the water. the older (pre '16 i think) had the big center hatch (wider) than the '16+ models.

Originally Posted by BenCantrell

I have a confession to make. Lately I've been doing all my landings backwards, and I've become so comfortable doing it that way that I've been leaving my rods in the rod holders.

I have seen some guys doing this, is it much easier than surfing in forwards? Maybe i will have to give this a shot.

[Pocoloco]

learned that trick long ago after trying my first surf landing with my P.A.
expensive lesson