hobie tank repairs - Kayak Fishing Adventures on Big Water’s Edge

TJones · 01-06-2013, 08:15 AM

yesterday i had two serious fails . first i filled the tank with macs , and while they were slashing around to the brims capacity, broke my connection where i had by passed my failed switch. i notice the the macs were getting sleepy eyed and quiet.

. so i release them , did a temporary fix , and back in business. at end of day when i went to unplug battery , pulled wire out of socket. is it time to rewire the tank? tank is more than a couple years old. any input would be appreciated. having the bait tank is great , but it always seems like something is always going wrong .first switch , thens its batteries , then clogs with pump. now wiring issues .

. as far as clogs with intake and sea grass, i did discover something pretty good. i bought a screen from home depot that has rubber on edges , i believe used for sink replacement . i trimmed the rubber a little , and placed behind black nipple of intake tube. it does make it more restrictive , but not enough to hinder flow. keeps grass out. one problem solved, for now. thanks again for any suggestions or help with wire issues. when i trimmed back wire to reconnect , i noticed it looks corroded under insulation and some what brittle. is that normal?

jaws197 · 01-06-2013, 10:07 AM

Had the same problem with my hobie tank at the switch, had to scrape off the clear insulation and re-solder the corroded terminal switch had failed then marine gooped the heck out of it.

I'm going to try your suggestion about the intake as I am tired of it sucking up EVERY piece of eel grass in the ocean!!! You would think that a tank that cost $200 would be made a little better with a little more thought about it's potential for pulling in foreign material (eel grass)!

TJones · 01-06-2013, 11:02 AM

there will be 2 screen replacements .about the size of a penny. i trimmed almost all the rubber on edges of screen and gently pressed it into the intake tube after removing the black nipple. replace black nipple and you are done. after a few launching and landings some sand will collect on screen, but not enough to stop flow . a few good pumps with peddles to get flow going to prime the tank is all that is needed. gallons per minute flow rate is reduced , but nothing that affects bait. one thing is for sure . grass is not going up inside.

. been using for about 4 outings . so far , so good.

DanaPT · 01-06-2013, 12:14 PM

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top. Because of the screen it's difficult to plug the in-take tube. IF something does get caught, moving around usually dislodges the debris..

Used to get clogged in the kelp until I began using this solution.

BrokeLoser · 01-06-2013, 12:24 PM

Quote:

Originally Posted by DanaPT

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top. Because of the screen it's difficult to plug the in-take tube. IF something does get caught, moving around usually dislodges the debris..

Used to get clogged in the kelp until I began using this solution.

Awesome idea...is that found at Home Depot? Does it restrict flow a bunch?

StinkyMatt · 01-06-2013, 12:42 PM

About a year ago I got tired of the connections and switch issues. Completely eliminated the switch and rewired the tank. At the battery I use a red/white connector like the ones found at automotive stores for .99 cents. When you make a wire to wire connection put on shrink tubing And then goop it all over. When you are ready to turn on tank, you turn around and plug in, simple.

I have not had one tank related issue in a year.

jorluivil · 01-10-2013, 10:01 AM

Quote:

Originally Posted by BrokeLoser

Awesome idea...is that found at Home Depot?

????

maui jim · 01-10-2013, 07:41 AM

Quote:

Originally Posted by DanaPT

I've been using a drain plug screen for sinks. These are also sold in pairs. The Nylon type work best. Simply put it on like a condom and zip tie the top.

Used to get clogged in the kelp until I began using this solution.

I Never used a zip tie on a condom...

Strange comparison....

jorluivil · 01-10-2013, 10:00 AM

I followed what Matt did and went straight battery to pump. Unlike Matt, the thing that I don't like about it is the 'reach around'.

01-06-2013, 08:15 AM	#1
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	hobie tank repairs yesterday i had two serious fails . first i filled the tank with macs , and while they were slashing around to the brims capacity, broke my connection where i had by passed my failed switch. i notice the the macs were getting sleepy eyed and quiet. . so i release them , did a temporary fix , and back in business. at end of day when i went to unplug battery , pulled wire out of socket. is it time to rewire the tank? tank is more than a couple years old. any input would be appreciated. having the bait tank is great , but it always seems like something is always going wrong .first switch , thens its batteries , then clogs with pump. now wiring issues . . as far as clogs with intake and sea grass, i did discover something pretty good. i bought a screen from home depot that has rubber on edges , i believe used for sink replacement . i trimmed the rubber a little , and placed behind black nipple of intake tube. it does make it more restrictive , but not enough to hinder flow. keeps grass out. one problem solved, for now. thanks again for any suggestions or help with wire issues. when i trimmed back wire to reconnect , i noticed it looks corroded under insulation and some what brittle. is that normal?

01-06-2013, 11:02 AM	#3
TJones Senior Member Join Date: Jan 2012 Posts: 2,526	look for small package there will be 2 screen replacements .about the size of a penny. i trimmed almost all the rubber on edges of screen and gently pressed it into the intake tube after removing the black nipple. replace black nipple and you are done. after a few launching and landings some sand will collect on screen, but not enough to stop flow . a few good pumps with peddles to get flow going to prime the tank is all that is needed. gallons per minute flow rate is reduced , but nothing that affects bait. one thing is for sure . grass is not going up inside. . been using for about 4 outings . so far , so good.

01-10-2013, 10:00 AM	#9
jorluivil Senior Member Join Date: Apr 2010 Posts: 6,856	I followed what Matt did and went straight battery to pump. Unlike Matt, the thing that I don't like about it is the 'reach around'. __________________ www.facebook.com/Teamsewer

01-06-2013, 10:07 AM	#2
jaws197 Senior Member Join Date: Apr 2012 Location: Poway, CA Posts: 148	Had the same problem with my hobie tank at the switch, had to scrape off the clear insulation and re-solder the corroded terminal switch had failed then marine gooped the heck out of it. I'm going to try your suggestion about the intake as I am tired of it sucking up EVERY piece of eel grass in the ocean!!! You would think that a tank that cost $200 would be made a little better with a little more thought about it's potential for pulling in foreign material (eel grass)!

01-06-2013, 12:42 PM	#6
StinkyMatt Senior Member Join Date: Jun 2010 Location: Under a bridge Posts: 2,169	About a year ago I got tired of the connections and switch issues. Completely eliminated the switch and rewired the tank. At the battery I use a red/white connector like the ones found at automotive stores for .99 cents. When you make a wire to wire connection put on shrink tubing And then goop it all over. When you are ready to turn on tank, you turn around and plug in, simple. I have not had one tank related issue in a year.