|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Community | Calendar | Today's Posts | Search |
|
Thread Tools | Display Modes |
|
07-08-2012, 11:00 PM | #1 |
Senior Member
Join Date: Apr 2010
Posts: 6,856
|
Pacific Anglers Seat for Hobie
Review of day 1:
Its sucks!!! Ok, it doesn't suck, its actually a great seat but its not built for the Hobie. The morning started OK but went south fast, I mean really fast.....my thoughts went from 'cool' to 'I'm ready to throw this thing in the water' almost immediately. At one point I looked up at the sky and prayed to the Man to give me the strength to survive the ordeal. The biggest problem: when you start to peddle you tend to put pressure on the upper part of the seat, this causes the lower part of the seat to slide forward. Eventually, you'll get to a point when you're laying with your back on the bait tank and you're staring up at the sky. This is the point where you start praying to the Man above. The buckles that are supposed to hold the straps in place and keep them from sliding only work if there is constant tension on them, the minute you release/relieve them of any tension the straps start to slip and this is what causes the bottom half of the seat to slide forward. I'm trying to avoid using the bolts that the standard Hobie seat comes with but that may be the solution. I played around with the seat most of the day and finally got it to stay in its place for a few hours but the minute that I got tired and tried to lean back I must have put to much pressure on the upper half of the seat and this caused the bottom half to slide out. I have a few solutions other than the bolt thing that I think will work but before I do any modification I going to give it another try tomorrow. I fished from about 6am until 3pm, considering how much I had to deal with and the stress I went through my back doesn't feel to bad. Lets see what day two brings
__________________
www.facebook.com/Teamsewer |
07-09-2012, 04:35 AM | #2 |
Senior Member
Join Date: Sep 2011
Posts: 598
|
Use a yoga matt underneath the seat. I seen people use it so they don't slide around.
|
07-09-2012, 06:48 AM | #3 |
Member
|
I have been using one on my Revo and have not had any problem with it I have a couple of non-factory pad eyes installed in the back though and that seems to hold everything in place. I think Andy (at OEX Sunset Beach) set this one up I'm sure he could help with yours. They are a great seat comfy and with enough support for long hours on the water.
Darren |
07-09-2012, 07:29 AM | #4 |
Team Keine Zugehörigkeit
Join Date: Nov 2010
Location: Way out there
Posts: 2,854
|
Had the same prob. I tied a knot in the straps in the back and using the stock hobie pad eyes, and added a pad because I got no arse.
__________________
Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ |
07-09-2012, 03:33 PM | #5 |
Senior Member
Join Date: Feb 2012
Location: SoCal
Posts: 196
|
Did you ever try the inflatable hobie seat? I broke down at FHS a bought it. I use both the original seat plus the inflatable for double the cushion. My A$$ has been thanking me ever since.
|
07-09-2012, 03:41 PM | #6 |
Senior Member
Join Date: May 2011
Location: I.E.
Posts: 179
|
|
07-10-2012, 08:39 AM | #7 |
Senior Member
Join Date: Apr 2010
Location: OC
Posts: 146
|
Good to know, been considering a new seat but wasn't sure which would work well on the Outback. Thanks for being the Guinea Pig...I can picture you out there cussing at the sky haha Hope you can make it work, looks like a great seat.
My Malibu had the COD Apex ( http://www.kayakfishingsupplies.com/...1-Kayak/Detail) which had a second set of straps to hold the bottom in place to keep it from doing that thing yours did. It was a great seat, especially with the COD inflatable pad (no longer available). I'm considering that seat again, or the GTS Elite, and adding a few padeyes to hold the rear straps, and slapping my $40 iComfort on that. Gotta quiz Andy on it tho to see if it'll work. |
07-10-2012, 09:25 AM | #8 |
Senior Member
Join Date: Sep 2005
Posts: 1,921
|
Not sure if there are the same padeyes on the Outback, but on my Hobie Adventure there were stock 2 padeyes right behind the seat that were perfect to attach to. If there aren't on yours, you might want to consider adding a couple stainless or brass ones where the seat buckles would naturally attach to. Before I had it adusted correctly, I tried attaching the aftermarket seat using the Hobie posts screwed into my new seat, but that didn't work too well.
My personal preference is to have the back straps on the seat as tight as they can possibly go, so there is no way the bottom of the seat can move on you. Once you get the new seat dialed in once, it is a whole night and day difference vs. the old stock seat. |
|
|