|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Community | Calendar | Today's Posts | Search |
|
Thread Tools | Display Modes |
|
04-18-2011, 10:42 AM | #1 |
Senior Member
Join Date: Feb 2011
Location: Corona, CA
Posts: 472
|
Drag replacement...what do you use?
I need to replace the drag system in a Daiwa Sealine 30. I've never done this before but I'm eager to learn how to service my own reels...plus it looks like Alan Tani's website makes 'do it yourself' a no-brainer...we'll see.
Who's washers and what grease are you using? It seems the Smooth Drag carbontex washers are the ones to go with from what I've been reading? Do some really use automotive gear oil in their reels? Thanks! |
04-18-2011, 11:02 AM | #2 |
Float Tuber
Join Date: Mar 2005
Posts: 243
|
Any type of grease will work for the side plates , sleeve and nuts. As for the drag nothing but Cals, or shimano grease. If you use regular grease on the drags you will have problems with your drags slipping.
|
04-18-2011, 11:40 AM | #3 |
Banned
Join Date: Mar 2009
Location: on the road...
Posts: 598
|
For drags there really arn't many options....smoothdrag being what most people use. And like buttchaser said, use only cals, or shimano grease on the drags.
As for the sealine 30 rebuild, Alans site is a great resource. Once you are comfortable rebuilding that reel, all the other star drag reels will be VERY similar. The lever drags are even easier IMO. One helpful hint I can give you to supplement all the info on Alans site has to do with the bearing and whether to grease or oil. On alan's site he recommends pulling all the shields on all the bearings and either packing them with grease, on the geartrain bearings, or oil, for the spool shaft bearings to maximize freespool. While I agree with packing all the geartrain brearings with grease and leaving them open, I havn't had much luck leaving the spool bearing open with oil (they corrode quickly). I think a big part has to do with the wetter kayak environment. So here is what I do...on my reels which freespool is not a huge deal (all my bait rods, and yoyo) I open and grease ALL the bearings. It really doesn't affect the freespool that much, and makes the service intervals much longer, and usually the bearing are reusable. For the jigsticks, where obviously freespool is an issue..... I leave the spool bearing factory sealed and just replace them when they start go bad. Bearing are fairly cheap, and the shielded bearing last much longer for me on the yak. Also remember to grease all the screws when you re-assemble. Locally, Squidco stocks tons of spare parts, bearing and drags. They generally have any bearing, or drag washer you need in stock. Have fun!! |
04-18-2011, 01:19 PM | #4 |
Senior Member
Join Date: Jun 2010
Location: Under a bridge
Posts: 2,169
|
Just serviced most of my reels. Waaay easy. I did not remove any bearing shields at this time, still alitlle nervous about that part. Just work slowly in a nice well lit place and have a towel to work over, so that parts don't roll anywhere on you. Most fishing stores have some type of oil and reel grease, I am unable to recommend any particular brand. Alan will sell you parts too, I think/ or he'll steer you to the proper source.
Sealine the easiest reel I have, it took me longer to do a Penn 113. Have fun! |
04-18-2011, 07:23 PM | #5 |
Team Keine Zugehörigkeit
Join Date: Nov 2010
Location: Way out there
Posts: 2,854
|
Cals and carbontex, Yamaha grease for the bearings if you repack them, just like allan says.
__________________
Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ |
04-18-2011, 08:08 PM | #6 |
Senior Member
Join Date: Sep 2006
Location: Bay Ho
Posts: 1,382
|
I use Cal's Grease on the drag washers.
-You only need a little, wipe off any excess with your finger. The Sealine X has a well sealed drag system, and rarely (if ever) does it ever see water intrusion. On the Sealine X its good practice to pack the handle bearing (inside and outside) with Cal's grease, and the threads on the handle shaft. Use Reel X on the Spool Bearings - You want them to spin free and smoothly. ---------------------------- One more thing... These reels have metal shields of their bearings. If a bearing feels a little rough try soaking it in kerosene, then blowing it out with compressed air. If it spins well after that lube it with Reel X and reassemble. If the bearing is toast, buy a new 3 piece set from Smooth Drag. They have very good quality replacement bearings at a fair price. Squidco and Charkbait carries everything you need.
__________________
|
04-18-2011, 10:39 PM | #7 | |
Senior Member
Join Date: Sep 2010
Location: San Diego, CA
Posts: 103
|
Quote:
removing the shields is actually one of the easier things I have learned to do in servicing reels. Use a very small sized hook. smallest you have is best. Something like a size 8 mosquito is what I like to use. maybe cut one off a sabiki in a pinch? You will see a small little metal clip around the edges of the bearing that holds the shield in place. get the point of the hook up against the edge of the clip and just get it slightly underneath and apply gentle upward pressure. Might want to keep your finger on the other side of the clip or do this some place where you will not lose small parts. Once the clip is free just turn the bearing upside down and shake it gently and the shield should fall out. If that doesn't work use the point of the hook and be very gentle and use that to free the shield. Do the same for the other side. Be careful with the shields and little retaining clips don't lose or bend them(have never had a problem). It's easy to put them back in after you flush the bearing and then pack with grease or apply light oil- whatever. Just put the shield back in, then the clip. As long as you have fine motor control and don't apply wildly more pressure than is required to do the job then it will be fine. also cals grease is great. I use it for drags. Also pack non-spool bearings with it. Will use it for gears or whatever else sometimes as well. One thing worth mentioning is that the stuff is probably NOT a consumer-grade product(in terms of safety) so use some gloves if it doesn't interfere with the job too much. |
|
|
|