Tape Measure - Kayak Fishing Adventures on Big Water’s Edge

dsafety · 06-06-2010, 09:29 AM

A recent thread made me wake up to the fact that I have not been carrying some required items on my yak when out fishing. Most notably missing have been a landing net and tape measure. I have a net and will start packing it but what is the best kind of measuring device to have on a kayak?

I have seen the vinyl stickers that look tacky and probably will not stay attached to a kayak hull. I have also seen adhesive-backed tapes that are made of sturdy materials but am concerned that these will not stick to the hull either.

An Internet search found some people mounting aluminum rulers to their boats, again, maybe not ideal for a kayak. Still others carved a scale into the plastic or marked a scale with tape or a sharpie.

For the time being, I will commandeer my wife's sewing tape and stick it in a pocket of my PFD but I suspect that there is a better way.

What kind of measuring device works best in our environment? Please weigh in.

Bob

Aaron · 06-06-2010, 10:10 AM

My aluminum rulers are great. Why wouldn't you like them? They have a clear coat on them to keep the oxidation off, though with some pretty easy maintenance, aluminum does fine in the salt. They were cheap too. A few bucks a piece from my local hardware store. Mounted them on both sides of the boat for convenience with 4 pop rivets in each. I don't even notice they are there until I need them. But the sewing tape will work too and I ran that for a bit...until my wife needed it and killed me b/c the ends had rusted off!

Only other suggestion I can make is to make sure you figure out where you want to mount them while sitting in the boat. I had a friend who's rulers ended up on the sides of the boat b/c that where they fit best, but once you sat in the boat, you couldn't see them at all.

Bpcode3 · 06-06-2010, 10:17 AM

Quote:

Originally Posted by dsafety

I have seen the vinyl stickers that look tacky and probably will not stay attached to a kayak hull. I have also seen adhesive-backed tapes that are made of sturdy materials but am concerned that these will not stick to the hull either.

Bob

Found and chopped one down to size for my paddle, just slit it at the center and put it on the paddle shaft, and has worked fine for about a year now with no interference. I should mention a little fading due to usage, but still a decent reference.

GregAndrew · 06-06-2010, 03:27 PM

I also use a paddle mounted sticker. It does not get any easier to quickly measure a fish than to lay it across the paddle on your lap. You can also put your paddle in the water to check the fish without taking it out. I have worn through a few of them, but they are only a few bucks to replace. Remember to find the part of your paddle that floats up and lays on top naturally to determine where you put the sticker. The first one I applied would always roll to the bottom of the paddle on my lap. Also, clean your paddle with alcohol or similar before you apply the sticker. They are available at Bass Pro in a few types and Cabelas has them too.

baitcasterboy20 · 06-06-2010, 04:23 PM

sometimes they have stickers to stick on the side of your kayak, but otherwise just carry a tape measurer or make your own gadget. like glue put a sticker tape measurer on the landing net that you've just decided to bring you should try to keep whatever you don't need in the kayak out

bubblehide · 06-06-2010, 05:05 PM

I think we should also keep in mind just how we are supposed to measure fish, i.e., from a flat surface. So don't use a tape and follow the contour of the fish. I hope this is clear.

dsafety · 06-06-2010, 08:01 PM

Since I release most of the fish I catch, I do not pay much attention to size limits. I am sure that someone on this forum has all the important size limit info programmed in their brain.

Would someone please post the size limit restrictions of the fish that we typically catch around here.

Thanks,

Bob

Bpcode3 · 06-09-2010, 01:54 PM

Quote:

Originally Posted by bubblehide

I think we should also keep in mind just how we are supposed to measure fish, i.e., from a flat surface. So don't use a tape and follow the contour of the fish. I hope this is clear.

Yeah, but like GregAndrew mentioned, good for reference and for a quick glance, thats all its used for. You said it yourself, you can't get an exact measurement unless on a flat surface anyways, and thats not until you get back to land. Chances are, if you need to measure to make sure, probably not worth keeping anyways.

PescadorPete · 06-07-2010, 09:40 AM

I use a thick Sharpie marker to mark each side along the top edge of the yak. A short port to starboard tick mark at the zero mark is about even where I sit and the few necessary lengths are marked forward of that. The length is written at each mark. I can bring the fish alongside, hold the tail at the zero mark and point the nose forward to measure. The marks require an occasional touchup during the season.

06-06-2010, 09:29 AM	#1
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Tape Measure A recent thread made me wake up to the fact that I have not been carrying some required items on my yak when out fishing. Most notably missing have been a landing net and tape measure. I have a net and will start packing it but what is the best kind of measuring device to have on a kayak? I have seen the vinyl stickers that look tacky and probably will not stay attached to a kayak hull. I have also seen adhesive-backed tapes that are made of sturdy materials but am concerned that these will not stick to the hull either. An Internet search found some people mounting aluminum rulers to their boats, again, maybe not ideal for a kayak. Still others carved a scale into the plastic or marked a scale with tape or a sharpie. For the time being, I will commandeer my wife's sewing tape and stick it in a pocket of my PFD but I suspect that there is a better way. What kind of measuring device works best in our environment? Please weigh in. Bob

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

06-06-2010, 10:10 AM	#2
Aaron Senior Member Join Date: Apr 2010 Posts: 175	My aluminum rulers are great. Why wouldn't you like them? They have a clear coat on them to keep the oxidation off, though with some pretty easy maintenance, aluminum does fine in the salt. They were cheap too. A few bucks a piece from my local hardware store. Mounted them on both sides of the boat for convenience with 4 pop rivets in each. I don't even notice they are there until I need them. But the sewing tape will work too and I ran that for a bit...until my wife needed it and killed me b/c the ends had rusted off! Only other suggestion I can make is to make sure you figure out where you want to mount them while sitting in the boat. I had a friend who's rulers ended up on the sides of the boat b/c that where they fit best, but once you sat in the boat, you couldn't see them at all.

06-06-2010, 03:27 PM	#4
GregAndrew Senior Member Join Date: Mar 2009 Posts: 2,384	I also use a paddle mounted sticker. It does not get any easier to quickly measure a fish than to lay it across the paddle on your lap. You can also put your paddle in the water to check the fish without taking it out. I have worn through a few of them, but they are only a few bucks to replace. Remember to find the part of your paddle that floats up and lays on top naturally to determine where you put the sticker. The first one I applied would always roll to the bottom of the paddle on my lap. Also, clean your paddle with alcohol or similar before you apply the sticker. They are available at Bass Pro in a few types and Cabelas has them too.

06-06-2010, 04:23 PM	#5
baitcasterboy20 Member Join Date: Mar 2010 Location: south florida Posts: 69	sometimes they have stickers to stick on the side of your kayak, but otherwise just carry a tape measurer or make your own gadget. like glue put a sticker tape measurer on the landing net that you've just decided to bring you should try to keep whatever you don't need in the kayak out

06-06-2010, 05:05 PM	#6
bubblehide Senior Member Join Date: Jun 2008 Posts: 552	I think we should also keep in mind just how we are supposed to measure fish, i.e., from a flat surface. So don't use a tape and follow the contour of the fish. I hope this is clear.

06-06-2010, 08:01 PM	#7
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Since I release most of the fish I catch, I do not pay much attention to size limits. I am sure that someone on this forum has all the important size limit info programmed in their brain. Would someone please post the size limit restrictions of the fish that we typically catch around here. Thanks, Bob

06-07-2010, 09:40 AM	#9
PescadorPete Senior Member Join Date: Mar 2005 Location: Leucadia, CA Posts: 261	I use a thick Sharpie marker to mark each side along the top edge of the yak. A short port to starboard tick mark at the zero mark is about even where I sit and the few necessary lengths are marked forward of that. The length is written at each mark. I can bring the fish alongside, hold the tail at the zero mark and point the nose forward to measure. The marks require an occasional touchup during the season.