|
Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Display Modes |
|
09-23-2017, 11:42 PM | #1 |
Member
Join Date: Apr 2017
Posts: 76
|
Help Removing Transducer
Hello everyone.
I have decided to move my transducer to a scupper mount over the current goop mount that i have now based off of what I have heard about clarity and accuracy. One problem though, I cannot get the transducer off. It is just pushed into marine goop inside my kayak, but I could not for the life of me get it off. An advice? Has anyone had this problem before? Tight lines, Johnny |
09-24-2017, 07:25 AM | #2 |
Senior Member
Join Date: Sep 2010
Location: South OC
Posts: 1,606
|
I haven't done this before but I would surgically remove with a razor blade. Go slow and easy all the way around. Silicon vs plastic.... should cut easy.
|
09-24-2017, 09:57 AM | #3 |
Member
Join Date: Aug 2013
Location: Pine Valley when not fishing La Jolla
Posts: 2,643
|
I removed one before to remount it outside in the water. I very carefully used a sharp and pointed knife (Buck or some similar heavier blade knife) to start to get under the edges of the goop and the hull. Once I was able to get under the goop and lift up on it, it started separating form the hull and a had to break off and scrape what was on the transducer. Be real careful to not poke a hole in the hull, the knife has to be held flat against the hull and only attempt to start under the goop edges. After the goop starts to separate switch to using a wide flat screw driver and slide it under and the twist side to side. Might even try first to push on the outside of the hull were the transducer is mounted to flex the hull material at the area of the goop, to help start to separate the two. Good luck
__________________
MARK ......... 2016 MALIBU X FACTOR, 2020 SOLO SKIFF (Fishing Kayak on Steroids ) |
09-24-2017, 10:42 AM | #4 |
Señor member
Join Date: Mar 2005
Location: San Diego, CA
Posts: 1,627
|
Use a pry bar and hammer, I have taken off a few, never damaged the kayak.
http://www.homedepot.com/p/Estwing-1...B-15/202183846 |
09-24-2017, 01:41 PM | #5 |
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,948
|
flat head screw driver and a pair of pliers, once you get a corner of the goop up it comes off pretty easily
__________________
|
09-24-2017, 01:52 PM | #6 |
Senior Member
Join Date: Aug 2012
Posts: 1,823
|
exactly what i did
__________________
"Beware the lollipop of mediocrity; lick it once and you’ll suck forever." — Brian Wilson |
09-24-2017, 07:32 PM | #7 |
Member
Join Date: Apr 2017
Posts: 76
|
Thanks everyone for the help. I will try these out as soon as i can.
Tight lines, Johnny |
09-25-2017, 09:21 AM | #8 |
Member
Join Date: Apr 2017
Posts: 76
|
Thanks again everyone. After some time of using the only razor blade I had (which was unfortuanlty not that razor sharp) and a chisel, i safely removed the transducer without a scratch on either the kayak or the transducer. Once I got it off i discovered that my goop had multiple large bubbles under the traducer, so now I am very excited to see how clear it is now.
Thanks! Johnny |
09-25-2017, 10:44 AM | #9 |
Senior Member
Join Date: Jul 2012
Location: Oceanside, CA
Posts: 419
|
Please report what difference of clarity that you get with the mount on the outside vs inside hull.
I have been pondering moving my transducer outside somehow. I really like the inside mount as it is so clean having everything (wires, battery) in the hull vs outside.
__________________
|
Thread Tools | |
Display Modes | |
|
|