Hobie Outback Storage Stand -- Using a Heavy Duty Tool Stand - Kayak Fishing Adventures on Big Water’s Edge

5-20 · 12-15-2016, 11:17 AM

Just came into possession of a super nice 2015 Hobie Outback, the same one listed by Yakdout. Pretty stoked, I couldn't have done half as nice a job of rigging it as Brandon did. Really excited about having a boat again!

Anyway, I have the yak laying flat on the floor right now. I came across an older thread that suggested using a work stand like this one.

http://www.harborfreight.com/200-lb-...and-38778.html

Any of you use something similar? Any issues with the hull deforming in any way?

Even tho it comes with foam cushions, I would probably replace them with thicker pool noodles.

One thing, though. I keep on coming across those recommendations that say outbacks should be stored hull up or on a J rack, but having the seat side up would probably be the most convenient thing and I would really prefer to try to store my yak this way if its not really going to affect the hull.

On an unrelated note, I'm thinking I would really like to try to get out in SD Bay this Saturday or Sunday and try to find some Halibut. Any of you up for that?

Chuck D · 12-15-2016, 01:05 PM

I have the same rack and use it for my Outback. It does not fit it perfectly. With the shape of the hull it usually moves from one side to the other. It is also a little bit flimsy and can fall down at times. That being said it does work for my kayak when I need a mobile, light rack and it has not done any damage to the hull. It's a good investment, however there are a lot of better ideas out there with PVC if you have the time and ingenuity... Good luck, drag that trap through the bay at about 30ft with a mack and you should find a butt or two as well. Tight lines.

D

Rocketfish · 12-15-2016, 02:40 PM

I use a sawhorse which is a tad cheaper than your stand, but from the same store!

http://www.harborfreight.com/foldabl...rse-61979.html

it works with my 2015 outback, you just need to put the saw horses a little closer to the ends, upside down of course. I haven't noticed any deformations of any kind since it's upside down.

5-20 · 12-15-2016, 02:53 PM

Quote:

Originally Posted by Rocketfish

I use a sawhorse which is a tad cheaper than your stand, but from the same store!

http://www.harborfreight.com/foldabl...rse-61979.html

it works with my 2015 outback, you just need to put the saw horses a little closer to the ends, upside down of course. I haven't noticed any deformations of any kind since it's upside down.

Hmm, wouldn't I need two of them, making it more expensive than the stand I am interested in.

Haha okay, i'll probably give the stand a shot until I build something slightly better. Thanks.

Keep the halibut tips coming tho!!! 30 feet of water you say?!

5-20 · 12-15-2016, 09:38 PM

Picked up that exact harbor freight stand about an hour ago. Thought the package felt kind of light in the store, even for something rated up to #200. But at $20 it was worth a shot anyway.

Had the outback wobbling back and forth on it for five seconds and I told myself there was no way I was leaving the Hobie on that thing. Would've cried if I came back later to find it smashed in a bunch of pieces. That thing's got way too much mojo, I gotta make sure I carry that on somehow. So yeah I quickly put the yak back on the floor.

I think I'll sniff around Home Depot and see what I can throw together.

socal.beach.bum · 12-15-2016, 09:53 PM

Just look for an old jet ski stand on CL. Prob get one for about $100-$125. Caster for easy transport too. Perfect

Rocketfish · 12-16-2016, 10:21 AM

Quote:

Originally Posted by 5-20

Hmm, wouldn't I need two of them, making it more expensive than the stand I am interested in.

You're RIGHT! I think I got the pair during one of them sidewalk sales they frequently have. might've been $7 or $8 each. I do like that coleman option though.. it looks perfect and I won't have to mess with inverting my yak.

Saba Slayer · 12-16-2016, 12:13 PM

I have two storage racks I use...
One has PVC pipes for the upright PA storage and the other is just 2"x4"s for the upside-down storage (as approved by Hobie) of the Island Yaks.

Baja_Traveler · 12-15-2016, 02:46 PM

Might be more than you want to spend, but I use a Racor lift to get my PA14 off the garage floor so I can park my car under it. Works great with a couple of lengths of 2" pvc to cradle the hull tunnels.

https://www.amazon.com/Racor-PHL-1R-.../dp/B0009I8AO6

12-15-2016, 11:17 AM	#1
5-20 Senior Member Join Date: Apr 2014 Posts: 241	Hobie Outback Storage Stand -- Using a Heavy Duty Tool Stand Just came into possession of a super nice 2015 Hobie Outback, the same one listed by Yakdout. Pretty stoked, I couldn't have done half as nice a job of rigging it as Brandon did. Really excited about having a boat again! Anyway, I have the yak laying flat on the floor right now. I came across an older thread that suggested using a work stand like this one. http://www.harborfreight.com/200-lb-...and-38778.html Any of you use something similar? Any issues with the hull deforming in any way? Even tho it comes with foam cushions, I would probably replace them with thicker pool noodles. One thing, though. I keep on coming across those recommendations that say outbacks should be stored hull up or on a J rack, but having the seat side up would probably be the most convenient thing and I would really prefer to try to store my yak this way if its not really going to affect the hull. On an unrelated note, I'm thinking I would really like to try to get out in SD Bay this Saturday or Sunday and try to find some Halibut. Any of you up for that?

12-16-2016, 12:13 PM	#8
Saba Slayer Senior Member Join Date: May 2007 Location: Palos Verdes Posts: 1,857	Sawhorses I have two storage racks I use... One has PVC pipes for the upright PA storage and the other is just 2"x4"s for the upside-down storage (as approved by Hobie) of the Island Yaks. __________________ Jim / Saba Slayer

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

12-15-2016, 01:05 PM	#2
Chuck D Senior Member Join Date: Jun 2010 Location: Bay Park Posts: 559	I have the same rack and use it for my Outback. It does not fit it perfectly. With the shape of the hull it usually moves from one side to the other. It is also a little bit flimsy and can fall down at times. That being said it does work for my kayak when I need a mobile, light rack and it has not done any damage to the hull. It's a good investment, however there are a lot of better ideas out there with PVC if you have the time and ingenuity... Good luck, drag that trap through the bay at about 30ft with a mack and you should find a butt or two as well. Tight lines. D

12-15-2016, 02:40 PM	#3
Rocketfish Senior Member Join Date: Mar 2015 Location: North O.C. Posts: 156	I use a sawhorse which is a tad cheaper than your stand, but from the same store! http://www.harborfreight.com/foldabl...rse-61979.html it works with my 2015 outback, you just need to put the saw horses a little closer to the ends, upside down of course. I haven't noticed any deformations of any kind since it's upside down.

12-15-2016, 09:38 PM	#5
5-20 Senior Member Join Date: Apr 2014 Posts: 241	Picked up that exact harbor freight stand about an hour ago. Thought the package felt kind of light in the store, even for something rated up to #200. But at $20 it was worth a shot anyway. Had the outback wobbling back and forth on it for five seconds and I told myself there was no way I was leaving the Hobie on that thing. Would've cried if I came back later to find it smashed in a bunch of pieces. That thing's got way too much mojo, I gotta make sure I carry that on somehow. So yeah I quickly put the yak back on the floor. I think I'll sniff around Home Depot and see what I can throw together.

12-15-2016, 09:53 PM	#6
socal.beach.bum Senior Member Join Date: Aug 2012 Location: Palos Verde, CA Posts: 636	Just look for an old jet ski stand on CL. Prob get one for about $100-$125. Caster for easy transport too. Perfect

12-15-2016, 02:46 PM	#9
Baja_Traveler Senior Member Join Date: Nov 2005 Location: Table 17, Bay Park Fish Co. Posts: 943	Might be more than you want to spend, but I use a Racor lift to get my PA14 off the garage floor so I can park my car under it. Works great with a couple of lengths of 2" pvc to cradle the hull tunnels. https://www.amazon.com/Racor-PHL-1R-.../dp/B0009I8AO6