Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 03-29-2015, 10:25 AM   #1
beardedguy
gurmpy old one
 
Join Date: Apr 2007
Location: El Cajon
Posts: 80
Help fixing a rod

Hi All,

Need a little help. A reel seat on one of my bait casting rods has come
loose. The cork above and below is fine but the reel seat will twist.
Anyone know how to fix this?

Thanks, Rich
beardedguy is offline   Reply With Quote
Old 03-29-2015, 10:30 AM   #2
bubblehide
Senior Member
 
Join Date: Jun 2008
Posts: 552
Drill a couple small holes through the reel seat, but not the blank. Then inject some 5 minute epoxy once you have the reel seat aligned properly.
bubblehide is offline   Reply With Quote
Old 03-29-2015, 10:31 AM   #3
Goose1993
Senior Member
 
Goose1993's Avatar
 
Join Date: Mar 2015
Location: San Diego
Posts: 115
What kind of rod? If it is a Shimano they should fix it for free and Calstar/seeker are pretty good about helping you out too I hear.

But if its older or you don't want to wait a month for the manufacturer to fix it, try going MM rods in Point Loma. They specialize in custom making rods, so I'm sure they can fix the seat of your rod as well.

Here's there info

3016 Garrison Street, San Diego, CA 92106
Phone:(619) 390-0379
Goose1993 is offline   Reply With Quote
Old 03-29-2015, 10:36 PM   #4
tomahawk
Senior Member
 
Join Date: Aug 2012
Posts: 109
what bubblehide said to do will work but you need an adhesive with a really low viscosity. something close to water. you could try heating the epoxy. i would not try 5 minute epoxy because the heat makes it runny but also speeds up the cure. maybe a 5 min with mixing nozzle, preheat both parts, and inject. i have never done this it is pure speculation.
tomahawk is offline   Reply With Quote
Old 03-29-2015, 10:40 PM   #5
bubblehide
Senior Member
 
Join Date: Jun 2008
Posts: 552
I've done it with the self mixing injectable type. Just keep in mind that everything needs to be right before hand. the holes need to be the right size for the injector, and the handle needs to be aligned correctly. You can do it with a slow cure, but you will need a monoject type syringe to inject it is, and then tape off the holes until the epoxy is set, so you don't get leakage.
bubblehide is offline   Reply With Quote
Old 03-30-2015, 01:03 AM   #6
FlyFishinYakr
Senior Member
 
FlyFishinYakr's Avatar
 
Join Date: Mar 2011
Location: Nor Cal...30 min from Bodega/Tomales Bay, 1hr from Clear Lake, 2+ hr to Berryessa & the Delta
Posts: 729
Hard to tell if you can fix without a picture. Not sure what kind of reel seat...split, solid, through touch, etc.
What brand is it?
It sounds like something a manufacturer/rod builder would have to repair.
FFY
FlyFishinYakr is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 11:59 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.