Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 03-30-2013, 12:01 PM   #1
tomahawk
Senior Member
 
Join Date: Aug 2012
Posts: 109
Sealing stealth 14 hatches

My stealth 14 gets water in both main hull and the "storage comparment" next to the bait tank. For the storage compartment it is obviously from the hatch (no other way in). Which part of the hatch is unclear. It could be leaking where the hatch attaches to the kayak or where the hatch opens and closes. Any ideas? I am thinking of drilling out all the rivet and using marine goop between the hatch and kayak. The hatch itself is more of a mystery on how I would improve that. The main hull potentially has the the hatch next to the bait tank, the rod holders, and gator hatch in addition to the obvious, hull leaks. Same fixes could apply to the hatch and rod holders. There are no obvious holes in the hull, if the hull is leaking I would guess it woulld be a one of the scuppers. For a figure of merit, I was out 5 hours last week in LB harbor, no real swell, didn't get swamped by a wake, just some wind chop. I had about a small dixie cup worth of water in the storage compartment and about a gallon in main hull. I have heard people on this site talk about filling the kayak with water to check for leaks but the engineer in me is saying that is a bad idea.
Thanks for reading and any responses,
Tom
tomahawk is offline   Reply With Quote
Old 03-30-2013, 12:12 PM   #2
jruiz
Large Member
 
Join Date: Jul 2012
Location: La Verne, CA
Posts: 1,011
I'm a rocket scientist and a part time brain surgeon and I put about a gallon of water in the hull to find leaks below the water line and soapy water and mild air pressure through the drain hole to find leaks above water line. My leaks were most things that had pop rivets like hatches and flush mount rod holders
jruiz is offline   Reply With Quote
Old 03-30-2013, 01:19 PM   #3
Dannowar
Senior Member
 
Dannowar's Avatar
 
Join Date: Aug 2012
Posts: 1,823
It's definitely the front hatch that's letting in the majority. I'd put some weather seal along the bottom of the gator hatch. I really do t understand the need for a gigantic hatch in the front. Just more chances its gonna leak
__________________
"Beware the lollipop of mediocrity; lick it once and you’ll suck forever." — Brian Wilson
Dannowar is offline   Reply With Quote
Old 03-30-2013, 02:48 PM   #4
tomahawk
Senior Member
 
Join Date: Aug 2012
Posts: 109
Jruiz - If you would have said brain surgeon and part time rocket scientist... with the leak rate fairly low, I didn't think moving a few gallons of water around inside the kayak would be perceptive enough. I am not sure i'd be able to check the scuppers that way. In my initial comment, I really meant it didn't sound good to load 360 lbs of water in the kayak to get the same water line on the inside of the kayak that I have with me plus gear (260 for me + 60 for kayak +40 for gear) on the outside. I like the soapy water and air pressure and I am deinitely going to try that.
Dannowar - My son has the stealth 12 with the same gator hatch and basically gets nothing inside. Next time out I am going to snag his gator hatch. I wasn't thinking it was the GH just because the last time out it was pretty calm and i still got a fair bit inside.
tomahawk is offline   Reply With Quote
Old 03-30-2013, 05:21 PM   #5
ful-rac
Emperor
 
ful-rac's Avatar
 
Join Date: May 2009
Location: Buena Park
Posts: 3,649
Most of your water is probably coming in from the side hatches. Raise the back end up with your wheels, take your garden hose and put some water on the side hatches, watch for leaks. If your stealth was like mine you'll get some water in it. You can try sealing with goop, hopefully that will help. Always remember to check once in awhile for water entering the hull especially on those rough days, and pump out if you have to.
__________________
There's nothing colder than yesterday's hotdog.
ful-rac is offline   Reply With Quote
Old 04-01-2013, 10:36 PM   #6
tomahawk
Senior Member
 
Join Date: Aug 2012
Posts: 109
Tested the storage compartment yesterday. Leaks really bad between the hatch and the kayak (through the gasket). I want to drill out the rivets and marine goop the hatch down. Any ideas on replacing the rivets? I'd love to just replace them with SS machine screws and nuts but I don't believe I can reach that far in the inside.
tomahawk is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 08:07 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.