Line rigging fix-it tip needed to rerig Revo 13 rudder keeper - Kayak Fishing Adventures on Big Water’s Edge

Mongo Johnson · 11-06-2012, 05:47 PM

The rudder keeper bungee loops out of a fitting on the Revo stern. (Circled in yellow) My line has become frayed and I need to replace it.

I've got the line and would welcome and rigging tips. What's the tip to "open" or access the fitting that the stern buggee comes out of?

Do you access it by a twist of the fitting, or work at the fitting from inside from the rear hatch? I could not get my head in there.

Or, is the line just knotted inside?

I'd welcome any tips prior to poking at it.

steveooo · 11-06-2012, 05:58 PM

It will unscrew from the outside of the kayak. When it is off, simply thread the bungee through the hole, tie a knot on the backside, screw it back in an you are good to go.

Hobie makes a tool to unscrew them

I've never used the tool. Needle nose pliers have always worked well for me.

Mongo Johnson · 11-06-2012, 06:06 PM

I figured it was simple, but figured it better to ask than blindly twist away. Thanks.

jorluivil · 11-06-2012, 06:14 PM

Just like Steveooo said, long nose pliers work just as good as that tool.

StinkyMatt · 11-06-2012, 08:55 PM

Saws all.

bus kid · 11-07-2012, 05:24 AM

Use a torch to heat up the fitting to loosen it!

11-06-2012, 05:47 PM	#1
Mongo Johnson Senior Member Join Date: Jul 2012 Location: Long Beach Posts: 192	Line rigging fix-it tip needed to rerig Revo 13 rudder keeper The rudder keeper bungee loops out of a fitting on the Revo stern. (Circled in yellow) My line has become frayed and I need to replace it. I've got the line and would welcome and rigging tips. What's the tip to "open" or access the fitting that the stern buggee comes out of? Do you access it by a twist of the fitting, or work at the fitting from inside from the rear hatch? I could not get my head in there. Or, is the line just knotted inside? I'd welcome any tips prior to poking at it. __________________ A day on the water . . . priceless.

11-06-2012, 06:06 PM	#3
Mongo Johnson Senior Member Join Date: Jul 2012 Location: Long Beach Posts: 192	I figured it was simple, but figured it better to ask than blindly twist away. Thanks. __________________ A day on the water . . . priceless.

11-06-2012, 06:14 PM	#4
jorluivil Senior Member Join Date: Apr 2010 Posts: 6,856	Just like Steveooo said, long nose pliers work just as good as that tool. __________________ www.facebook.com/Teamsewer

11-07-2012, 05:24 AM	#6
bus kid Team Keine Zugehörigkeit Join Date: Nov 2010 Location: Way out there Posts: 2,854	Use a torch to heat up the fitting to loosen it! __________________ Não alimente os trolls------------Don't feed the trolls---------------インタネット荒らしを無視しろ

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

11-06-2012, 05:58 PM	#2
steveooo Senior Member Join Date: Sep 2005 Posts: 1,921	It will unscrew from the outside of the kayak. When it is off, simply thread the bungee through the hole, tie a knot on the backside, screw it back in an you are good to go. Hobie makes a tool to unscrew them I've never used the tool. Needle nose pliers have always worked well for me.

11-06-2012, 08:55 PM	#5
StinkyMatt Senior Member Join Date: Jun 2010 Location: Under a bridge Posts: 2,169	Saws all.