PA wood - Kayak Fishing Adventures on Big Water’s Edge

lowprofile · 10-24-2012, 09:38 PM

first question... what kind of wood are the guys using for the side boards on the PA's?

second. It's great to be able to stand up, but i try to do it whenever possible. Bass fishing, throwing swimmies under docks, jigging for squid and macs, tossing irons. I notice the floor flexes, and although its not showing any signs of wear, i feel it will over time. i'm between 245 and 250, so there is a little bit of weight being forced onto a relatively small area of deck space.

was thinking of cutting some 3/8" ply wood and fit it around the center hatch and cover the deck up to the mirage hole to displace some of the weight.

anyone try something like this or know of it being done? i know its a simple job but i dont want to do something that will ruin the yak. Also, I'm just going to lay it in, not drill or epoxy it. ill lacquer/paint it and put some grip tape on one side.

ericko · 10-24-2012, 09:51 PM

My pa 12 has alot of foam inside the area that i might stand dont know if this helps just another idea..

it came with the foam.

lowprofile · 10-24-2012, 10:00 PM

yeah, mine has foam too. made wiring it a pain.

Amish Ed · 10-25-2012, 10:01 AM

I'd be more worried about creating new stress points. They'd be in areas not designed to take the kind of pressure they would be getting.

GregAndrew · 10-25-2012, 10:37 AM

I would suggest Apitong for the deck wood. It is a sturdy hardwood that handles the Sun well and has a bit of water resistance. It is what they use for stakebed trucks. There is a similar wood available too that is sometimes used as a substitute (because of availablility), but I cannot remember the name of it.

taggermike · 10-25-2012, 11:00 AM

Teak is one of the best woods for sun and water exposure but it has become very expensive. Avitong-apitong?? is a good wood for exposure and its tough as well. Sand it smooth and use an oil coating and it should be good. Mike

Anthony179 · 10-25-2012, 02:49 PM

I work in a lumber yard in City of Industry. Teak goes for $23 a board foot. How much lumber and thickeness do you need. I have some teak in a 4/4 and 8/4 thick. Let me know. I can get you a piece at no charge. you just need to pick up. 626-274-0425

10-24-2012, 09:38 PM	#1
lowprofile #1 on fishstick's hitlist Join Date: May 2011 Location: Sea level Posts: 1,478	PA wood first question... what kind of wood are the guys using for the side boards on the PA's? second. It's great to be able to stand up, but i try to do it whenever possible. Bass fishing, throwing swimmies under docks, jigging for squid and macs, tossing irons. I notice the floor flexes, and although its not showing any signs of wear, i feel it will over time. i'm between 245 and 250, so there is a little bit of weight being forced onto a relatively small area of deck space. was thinking of cutting some 3/8" ply wood and fit it around the center hatch and cover the deck up to the mirage hole to displace some of the weight. anyone try something like this or know of it being done? i know its a simple job but i dont want to do something that will ruin the yak. Also, I'm just going to lay it in, not drill or epoxy it. ill lacquer/paint it and put some grip tape on one side. __________________ MLPA- My Largest Poaching Area

10-24-2012, 10:00 PM	#3
lowprofile #1 on fishstick's hitlist Join Date: May 2011 Location: Sea level Posts: 1,478	yeah, mine has foam too. made wiring it a pain. __________________ MLPA- My Largest Poaching Area

10-25-2012, 10:01 AM	#4
Amish Ed Senior Member Join Date: Jun 2005 Location: Grants Pass, OR Posts: 1,906	I'd be more worried about creating new stress points. They'd be in areas not designed to take the kind of pressure they would be getting. __________________ Amish Ed You can't catch it again if it's dead!

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-24-2012, 09:51 PM	#2
ericko Senior Member Join Date: Jun 2008 Location: Huntington beach Posts: 594	My pa 12 has alot of foam inside the area that i might stand dont know if this helps just another idea.. it came with the foam.

10-25-2012, 10:37 AM	#5
GregAndrew Senior Member Join Date: Mar 2009 Posts: 2,384	I would suggest Apitong for the deck wood. It is a sturdy hardwood that handles the Sun well and has a bit of water resistance. It is what they use for stakebed trucks. There is a similar wood available too that is sometimes used as a substitute (because of availablility), but I cannot remember the name of it.

10-25-2012, 11:00 AM	#6
taggermike Senior Member Join Date: May 2007 Location: Chula Vista Posts: 1,589	Teak is one of the best woods for sun and water exposure but it has become very expensive. Avitong-apitong?? is a good wood for exposure and its tough as well. Sand it smooth and use an oil coating and it should be good. Mike

10-25-2012, 02:49 PM	#7
Anthony179 A.T. Join Date: Nov 2008 Location: Ontario, CA Posts: 146	I work in a lumber yard in City of Industry. Teak goes for $23 a board foot. How much lumber and thickeness do you need. I have some teak in a 4/4 and 8/4 thick. Let me know. I can get you a piece at no charge. you just need to pick up. 626-274-0425