Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 09-28-2011, 05:56 PM   #1
sammysamsam
Senior Member
 
sammysamsam's Avatar
 
Join Date: Sep 2010
Location: whittier
Posts: 158
Battery box plug

Shot out a pm to Andy and figured i would see what you guys suggest also.

I cant deal with the battery plug for my bait tank anymore. The wires from the pump keep slipping out of the male plug that i plug into the battery box or it doesnt make good contact inside the female end. Tried electrical tape but that doesnt work. i already bought another battery plug from oex and it just doesnt tighten down enough to hold the wires.
What can i do? Plus, once you tighten down the little screws on the plug, there is no way to open them again or else you strip the small brass screws. Do you have any ideas other than buying another $7 dollar battery plug and going through the same process? Im just frustrated with this thing since my bait keeps dying.
Attached Images
File Type: jpg 2011-09-28 18.16.44.jpg (34.1 KB, 242 views)
sammysamsam is offline   Reply With Quote
Old 09-28-2011, 06:10 PM   #2
buttchaser
Float Tuber
 
buttchaser's Avatar
 
Join Date: Mar 2005
Posts: 243
Can you post some pictures of it?
buttchaser is offline   Reply With Quote
Old 09-28-2011, 06:22 PM   #3
sammysamsam
Senior Member
 
sammysamsam's Avatar
 
Join Date: Sep 2010
Location: whittier
Posts: 158
those wires do not stay in that plug. ideas?

Also, What do you guys use to keep the battery box from moving around inside the hatch?
sammysamsam is offline   Reply With Quote
Old 09-28-2011, 09:33 PM   #4
kobra
Senior Member
 
kobra's Avatar
 
Join Date: May 2005
Location: oceanside
Posts: 880
Quote:
Originally Posted by sammysamsam View Post
those wires do not stay in that plug. ideas?

Also, What do you guys use to keep the battery box from moving around inside the hatch?

Can you solder (sp?) the wires to the connector pins?
I keep my battery box in place with a small bungy cord wrapped around the sail mast tube on my Hobie.
kobra is offline   Reply With Quote
Old 09-28-2011, 09:53 PM   #5
Lets_Fish
Senior Member
 
Lets_Fish's Avatar
 
Join Date: Oct 2009
Location: Wildomar, CA.
Posts: 294
Try a weatherproof connection!

Try these out.

Hobie uses them on their bait tank and they are weather proof.

Here is a link: http://www.performanceplusconnection...nKit16_14.html

They have different sizes also. Purchase the ones that fit your wires.
Lets_Fish is offline   Reply With Quote
Old 09-30-2011, 10:03 AM   #6
habanero
Senior Member
 
habanero's Avatar
 
Join Date: Oct 2007
Location: SD
Posts: 133
Quote:
Originally Posted by Lets_Fish View Post
Try these out.

Hobie uses them on their bait tank and they are weather proof.

Here is a link: http://www.performanceplusconnection...nKit16_14.html

They have different sizes also. Purchase the ones that fit your wires.

FYI I use these all over the place and found this place for best prices:
http://www.thedetailzone.com/Wiring%20Aids.htm

This place for bulk:
http://www.mouser.com/_/?Keyword=Weatherpack
habanero is offline   Reply With Quote
Old 09-28-2011, 10:06 PM   #7
GregAndrew
Senior Member
 
Join Date: Mar 2009
Posts: 2,384
I prefer these outside the battery box.
http://www.amazon.com/Hopkins-47965-...271318&sr=1-11
I just drill 2 small holes in the box for the wires and goop them up.

I think the terminals are aluminum. I also have them permanently attached to my batteries so I don't have to mess around with the weak battery terminals.
GregAndrew is offline   Reply With Quote
Old 09-29-2011, 02:36 AM   #8
jorluivil
Senior Member
 
jorluivil's Avatar
 
Join Date: Apr 2010
Posts: 6,856
I had a the same issue so here's what I did.
  1. cut old wire off
  2. strip off outer cover(strip off just a little more than you'll need)
  3. flux both negative and positive strands thoroughly
  4. solder each wire, make sure the solder gets inside the strands
  5. measure each wires diameter making sure that each fits inside its respective hole, wire should have a snug fit
  6. measure and cut off excess wire
  7. if you have one insert outer protective cover over wire/cable
  8. loosen screw on plug, do not loosen to much or they will come off
  9. inside wires in their respective holes and tighten screw
When you tighten the screw it will dig itself into the solder and create a dimple as its tighhtened. The dimple will hold the wire in place and keep it from slipping out.

I went one step further and added marine goop to each hole where the wires fit and also gooped the section where the protective cover slips over the wire/cable. I insert and remove my plug every trip, its been almost a year since I did this and I have not had any issue to date.
__________________


www.facebook.com/Teamsewer
jorluivil is offline   Reply With Quote
Old 09-29-2011, 08:51 AM   #9
sammysamsam
Senior Member
 
sammysamsam's Avatar
 
Join Date: Sep 2010
Location: whittier
Posts: 158
Quote:
Originally Posted by jorluivil View Post
I had a the same issue so here's what I did.
  1. cut old wire off
  2. strip off outer cover(strip off just a little more than you'll need)
  3. flux both negative and positive strands thoroughly
  4. solder each wire, make sure the solder gets inside the strands
  5. measure each wires diameter making sure that each fits inside its respective hole, wire should have a snug fit
  6. measure and cut off excess wire
  7. if you have one insert outer protective cover over wire/cable
  8. loosen screw on plug, do not loosen to much or they will come off
  9. inside wires in their respective holes and tighten screw
When you tighten the screw it will dig itself into the solder and create a dimple as its tighhtened. The dimple will hold the wire in place and keep it from slipping out.

I went one step further and added marine goop to each hole where the wires fit and also gooped the section where the protective cover slips over the wire/cable. I insert and remove my plug every trip, its been almost a year since I did this and I have not had any issue to date.
So essentially you are just adding solder to the wire so the screw can dig into the wire, correct?



Quote:
Originally Posted by GregAndrew View Post
I prefer these outside the battery box.
http://www.amazon.com/Hopkins-47965-...271318&sr=1-11
I just drill 2 small holes in the box for the wires and goop them up.

I think the terminals are aluminum. I also have them permanently attached to my batteries so I don't have to mess around with the weak battery terminals.
Are these weatherproof?
sammysamsam is offline   Reply With Quote
Old 09-29-2011, 08:28 AM   #10
mtnbykr2
Senior Member
 
mtnbykr2's Avatar
 
Join Date: Sep 2009
Location: newbury park ca
Posts: 2,323
Quote:
Originally Posted by sammysamsam View Post
those wires do not stay in that plug. ideas?

Also, What do you guys use to keep the battery box from moving around inside the hatch?
the insulated connectors are the best, the connectors Greg used are just as good, as far as holding the battery in place I found a 2 1/2 inch wide by approx 12 inch long velcro strap that has a stainless buckle on it, fits aroud the battery with just enough extra left to wrap around the mast post holds tight enough that when I forget to remove the battery it stays in place even when loading the yak upside down
mtnbykr2 is offline   Reply With Quote
Old 09-29-2011, 08:44 AM   #11
Caballito
Member
 
Caballito's Avatar
 
Join Date: Apr 2007
Location: San Diego
Posts: 42
Go with Gregs soultion. You can buy them online cheap. Cut splice and solder them, followed by a couple coats of liquid electrical tape (west marine), then with electrical tape. Works great.
__________________
Caballito
Caballito is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 07:07 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.