drive rubbing
 

my mirage drive looks like it is chaffing the inside of the drive bay on my revo. mostly on one side . the yak is a 2012 . some wear is probably normal? do i wait till it is so weak and worn out , that it starts taking on water :paddleersmilie:. or is there something i can do ? possibly put some duct tape to slow down the wear and tear ? my mirage drive is a 2010 from my original outback. the drive has some slack in it . is this creating the problem? the black nylon legs are a little loose on the main shaft from use . any ideas?

Call Hobie

They can look pretty rough in there right out of the box, as excess is trimmed from the parting line. Post a photo

Thx
 

Copy ice. When I get back home I will snap a photo. I estimate .5 mm taking off. I think I have heard of failures around this area. So I want to keep close track of what's going on.

Can you post the pics please

just got back from lunch
 

:ack2: . let me go to garage . brb.

what pain
 

just to sync.

tossed in that picture of drive
 

so you could see the gap . if i could get some opinions on whether i should start thinking about replacing those nylon arms . i replaced a couple cables already that had a few frayed strands of wire . hopefully the other pictures can give you an idea of what i was referring to . maybe it is a minor concern ? or as i had mentioned before , like trying to slow the process down with tape?

Whoa nelly!!!!! Look at that gap on those drums! A gap that big on your drums is like having a real bad front wheel alignment on your car. Your tires are not going to wear evenly. Replace the drums ASAP!

drums are $16.50 a piece, I am guessing those saw an extended period of loose chains/cables at one time.

copy that
 

it is pretty obvious in picture. at least 1 mm gap. and of course noticeable slop in drive mechanism .that might be why i am having contact on side of drive bay. my drive is a 2010 and i think i did not lube the shaft until recently. when i took the yak out , it would be for long hours on water . i probably should have broken it down and lube it more often . i might just pick up a new drive and then start rebuilding this one as a backup . anyone else have any opinions ?

are you allowed to talk prices ?
 

on the forum?

Whats wrong with just calling Andy on the Phone?

Yeah... just buy two new drums and an axel. It will take 10 minutes to replace. Why spend $500 on a drive?

Also, since you have this problem. I wouldn't be surprised if the shaft running through your fins has a lot of wear on them too.

I take apart and clean my drives once a month.


Which do you prefer?

Preventative Maintenance:

The care and servicing by personnel for the purpose of maintaining equipment and facilities in satisfactory operating condition by providing for systematic inspection, detection, and correction of incipient failures either before they occur or before they develop into major defects.


Corrective Maintenance:

Corrective maintenance is a maintenance task performed to identify, isolate, and rectify a fault so that the failed equipment, machine, or system can be restored to an operational condition within the tolerances or limits established for in-service operations.

thx drake
 

i should break em down every now and then . how do i find the post on adjusting the drive?

scratch that
 

found link.

Or you can sell that drive to me cheap. I'll slap on a new set of drums in 15 min and have a like new drive.

systematic inspection, detection, and correction of incipient failures either before they occur or before they develop into major defects.

that's deep. I'm taking my drive apart this weekend.

Andy, when the drums are changed are there any non-reusable parts that would also need to be replaced?

No...

Mirage drives are actually incredibly simple. In order to service them you only need two open ended wrenches and a alan wrench.

Paper towels, q-tips, soapy water, and grease

Unless your cables are stretched to the point of the lock nuts being bottomed out, or your main axel has grooves from friction; there is nothing else you would need to change.